Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your wa...
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft....
This kit (Medium Cam Agitator Repair Kit, Washer Agitator Cam Repair Kit, Cam Agitator) is used to repair the agitator. These parts are located inside the agitator auger near the top. You will need t...
The direct drive drain pump (Whirlpool Direct Drive Washer Pump, Drain Pump, Washer Drain Pump, Water Pump) removes water from the washer during the drain cycle without the use of a belt. The pump is ...
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could c...
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. If the clutch lining ...
This part is found in your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire. If your machine is ...
This is a genuine OEM thrust spacer for your washer, and is also commonly known as a retainer ring. The spacer is about 2.5 inches in diameter, is made of plastic, and is white in color. It is used in...
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollabl...
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pierre
January 20, 2020
I can't remove the panel. I removed the 2 screws on the side in the back of the panel, tried to insert a putty knife on either side, but nothing is moving. Any suggestions? Thanks
For model number WTW5200SQ0
Hello and thank you for writing.
We are not sure which panel it is you are trying to open, but we believe it is the back panel.
Step 1
Unplug the Whirlpool washer and turn off the water lines. You should see a pair of hoses with oval handles near the wall. Turn the handles clockwise to shut off both the cold and hot water lines.
Step 2
Locate the screws on either side of the washer console. The console is the panel with the control dials that sits along the back edge of the top of the washer. Use a Phillips-head screwdriver to remove each screw.
Step 3
Slide the console toward the front of the machine. When the tabs under the console have cleared the slots in the top of the washer cabinet, lift it up and roll it open on its hinges.
Step 4
Unplug the console from the top of the washer. You will see several wires harnessed together that are connected to the washer. Press the tab on the plug and pull it out.
Step 5
Remove the flat, wavy silver metal clips that connect the top of the washer cabinet to the rear panel. There will be one clip located in the slots on each side in the area that is normally covered by the console. Use a flat head screwdriver to pry the ends of the clips out from the top of the cabinet. This will loosen the tension so that the other end slides down and out of the tab on the back pan.
Step 6
Slide the ends of the clips out from the back panel.
Step 7
Open the washer's lid and tilt the washer cabinet toward you, separating it from the back panel.
We hope this helps. Please contact us anytime if you require further assistance.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Charles
June 12, 2023
All hoses on back panel
Water leaks when filling
What do I order??
For model number WTW5200SQ0
Hi Charles, thank you for your inquiry. Based on the description that you have provided, we would recommend making sure that the water lines are not damaged. If that is not the case, then you may need to check the water inlet valve, part number PS11746765, as it is most likely faulty and may need to be replaced. We hope this sorts out your problem!
Hello Cesar, thank you for contacting us. The compatible timer for your model is part number PS11746777. If you need help placing an order for it, please feel free to give us a call!
Hello Randall, thank you for getting in touch. We would recommend checking the water inlet valve, part number PS11746765, to solve the problem. A faulty water inlet valve can cause the machine to not fill with water and hence resulting the timer to not start a cycle. We hope this helps!
Sometimes the tub will not spin at the end of the cycle. I can spin it by hand and then turn the spin on and usually it will start spinning like it’s supposed to
For model number WTW5200SQ0
Hi Allen, thank you for the question. We would suggest checking the clutch assembly, part number PS334641. It is responsible for spinning the basket during the spin cycle. You may need to replace it to fix the issue. We hope this sorts out your problem!
The job looked intimidating but turned out to be very easy. First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pum
... Read morep. The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed. One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary. Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs. Slip the new cogs into the underside of the cup, and slide the cup back down in the a
... Read moregitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out). Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
The instructions came with the repair kit, it was fairly simple and straight foward.
One bolt held the entire agitator unit in the washer, as well as held the upper and lower halves together. Once that nut was removed the two halves seperated and the plastic clutch pieces could easily be replaced wtih the new onces in the repai
... Read morer kit.
Very easy do-it-yourself repair! Took about 20 minutes because I was being cautious. Next time I could do it in 5 minutes.
