The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This part changes the transmission from agitation to spin mode. This actuator is for washers.
Actuator shifts the splutch and monitors the position of the splutch.
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Questions And Answers for WTW4900BW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
12 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dan
February 25, 2020
Lint left on clothes after wash. Is there a filter that could be clogged ? Thanks dan
For model number WTW4900BW0
Hi Dan,
Thank you for your question. There is a lint filter listed under your model number. This is a drain pump filter at the outer tub inlet. The part number listed under your model number for the lint filter is PS11750500. If you are finding lint on your clothes after a wash, this could be a result of overloading the washer. Try washing in smaller loads and check the tags on your clothes to see how the clothes should be washed. This may help reduce the lint on them. If you do need to place an order for the lint filter, you may order it either online, by visiting our live chat sessions, Monday to Friday from 8AM to 4PM EST, or by calling our customer service line at 1-888-738-4871 and anyone will be happy to assist you. We hope this helps. Thank you and have a great day.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Craig
February 23, 2020
Why is the washer loud during spin cycle
For model number WTW4900BW0
Hello, Thank you for your question. You will want to check into the Drive pulley, the bearings, the belt and the motor. We hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Dan Dobrinich
February 23, 2020
Washer leaves lint on clothes after wash is done
For model number WTW4900BW0
Hello and thank you for writing.
Excessive lint on clothes after washing may indicate that the water pump PS11757016 is clogged or faulty. When that happens, the wash and rinse water with all that suspended lint drains too slowly and leaves deposits on wet clothes. Remember to clean these regularly to prevent lint from redepositing on clothes. We hope this helps. Please contact us anytime if you require further assistance.
Have you had any other reports of this Whirlpool washing machine coming on by itself days weeks in a drain then spin (in the middle of the night i believe it went through a whole spin cycle before stopping. If away i hit the cancel. We have had the electric, (wires & box), plugin to confirm it was receiving proper amps & was probably grounded, and lastly the power cord. The washer was not 1 1/2 year old when it started this. I contacted lowe’s where it was purchased who advised me they would only warranty for 1 year so and would do nothing for me unless i wanted to purchase a new one. I happened to see you for parts and info on youtube and thought i would see if you had heard or had a clue as i have to keep it unplugged when not in use as it sits between my bedroom and all exits and i don’t want to awaken trapped inside a burning house because of the washing machine. Anyway and all help/advice is most appreciated.Sandra carson
For model number WTW4900BW0
Hello Sandra and thanks for writing.
Start here, then let us know what you see:
DIAGNOSTIC TEST
The washer must be empty and the control must be in the OFF
state before pressing the touch-pad sequence to start the test.
Starting the Test Mode
¦ Close the door.
¦ Push CONTROL/ON (if present on this model).
¦ Select the DRAIN/SPIN cycle.
¦ Select NO SPIN by pressing the SPIN SPEED touch-pad.
¦ Push PREWASH OPTION four times within five seconds. (If
PREWASH OPTION is not present on this model, press RINSE
HOLD four times within five seconds.) C:00 will light up on the
display.
If the Starting procedure fails, push the PAUSE/CANCEL touch-pad,
then repeat the starting procedure.
Test Program Control
In order to advance to the next step of the test procedure, push
PREWASH OPTION touch-pad two times. If PREWASH OPTION is not
present on this model, press RINSE HOLD two times.
We hope this helps. Please contact us anytime.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tim
November 14, 2021
Outlet is good but machine has now power
For model number WTW4900BW0
Hello Tim, Thank you for the question. If the appliance is getting power but not powering on, we suggest replacing the Control Board, PartSelect Number PS8768793. We hope this helps!
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer faile
... Read mored which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform
... Read moreation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.