This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your washer to tumble your clothes during the washer cycle. Your agitator will rotate one way, and not the other. The agitator dogs are what preven...Read moret the agitator from rotating in both directions, while allowing it to rotate in one direction. Your agitator cogs may be malfunctioning if you can manually rotate the agitator in both directions. If broken they will need to be replaced. Cogs can be found by simply removing the softener dispenser and then removing the agitator cap. The are attached to the agitator. This replacement part features 4 agitator directional cogs. There are 4 cogs per package that are made up of high-quality plastic. This part comes in white/beige.
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollable shaking and moving, loud noise, pumps but will not spin, or if your appliance will not agitate. This model is off-black in color and 3 inc...Read morehes in diameter. You will find this part inside the agitator in the middle of your washing machine. It is recommended to wipe down the barrier before putting the new seal on.
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging the drive motor to rotate the washer basket. The kit includes the clutch assembly, cam ring, spring, basket drive gear, pulley, and mounting n...Read moreut. Replacing this component can resolve issues such as noisy operation, slow or failed spinning, poor agitation, and excessive moisture in clothes after a cycle. In some cases, a burning smell may also indicate a failing clutch. Installation requires basic tools and should be performed with the appliance disconnected from power. Compatibility should be confirmed using your washer’s model number.
This washer lid switch is a critical safety component designed to halt the spinning motion of the tub when the lid is opened. Its primary function is to prevent accidental contact with moving parts during operation, reducing the risk of injury. The switch activates automatically, interrupting the spin cycle as soon as the lid is lifted. I...Read moref the switch becomes faulty, the washer may not spin or may continue spinning with the lid open, posing a safety hazard. Replacement is recommended if the switch is damaged or no longer functioning properly.
This genuine OEM drive belt is designed to transfer power from the motor to the drum in select Whirlpool, Maytag, Kenmore, and other compatible washing machines. Operating at 115 volts and 60 Hz, the belt enables the drum to spin and agitate during wash and spin cycles, ensuring effective cleaning and rinsing. Manufactured to Whirlpool’s ...Read morespecifications, this replacement part offers reliable performance and a precise fit. Common symptoms of a worn or broken belt include the drum not spinning, unusual noises, or a burning smell during operation. Replacing the belt can restore proper function and prevent further mechanical issues. Always verify compatibility with your specific model before ordering.
This suspension rod kit includes four rods designed to stabilize the wash tub in compatible top-load washing machines. By minimizing vibrations and excessive movement during wash and spin cycles, these rods help maintain balance and improve overall performance—especially when handling off-balance loads. Replacing worn or damaged suspensio...Read moren rods can resolve issues such as shaking, banging, or the washer shifting during operation. Installation requires unplugging the appliance and consulting the user manual for model-specific guidance. This kit is compatible with a range of washing machine models and is sold as a complete set.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Alan - For model number WTW4800BQ1
January 2, 2020
My washer when i put a full load in it will not spin when it does it does not get to close all the water out. I have replaced the belt clutch and electronica board
Hi Alan, thank you for your question. If your belt and control board is not the issue, then you may have to take a look at your gearcase and your motor for being the issue. Good luck with your repair.
4 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Tammy - For model number WTW4800BQ1
February 7, 2020
Washer will not finish a cycle it will wash drain but will not spin unless i cancel, then select, cycle then unplug and put it on drain in spin
Hello Tammy,
Thank you for your question. Our sources suggest replacing the lid latch assembly under part PS3497627 for your model to fix the spinning issues. We hope this helps.
I put a small load through, on regular cycle. The spin cycle did not function well. It did drain, but the clothes were soaking wet. Can't see if it's spinning because of the darn lid lock. I tried this a few times. Then i put it on the "spin and drain" cycle and it worked fine.Clothes were spun dry. So i know it spins. I have checked the belt and that was okay.
Hello Daniel, Thank you for your inquiry. We have researched your model and recommend checking the following parts to fix your issue: the shift actuator, the washer drive pulley, the gearcase, and the door lock. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you.
Where is lid switch assembly located? How do i get to it?
Hello and thank you for writing.
Lid switch # PS3497627 is in the list of compatible parts for your model number. For your convenience, we have attached the link to our repair video. We hope this helps. Good luck with your repair.
https://www.youtube.com/watch?v=u1DCXvPkWzM
We hope this helps. Please contact us anytime if you require further assistance.
Washer works great, except every wash it rattles like the load is unbalanced. It sounds like it’s trying to bang out of the casing. How can I fix this?
Hi Carrie, thank you for the question. The issue could be with the suspension system. We would suggest replacing the suspension rod kit, part number PS11703288. We hope this solves your problem!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
washer wouldn't agitate
955 of 1057 peoplefound this instruction helpful.
mike from Kent, WA
Easy
15 - 30 mins
Screw drivers, Socket set
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs. Slip the new cogs into the underside of the cup, and slide the cup back down in the a
... Read moregitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out). Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Read less
Was this helpful?
Thank you for voting!
top half of agitator did not move during wash cycle
288 of 337 peoplefound this instruction helpful.
dennis from new stanton, PA
Really Easy
Less than 15 mins
Socket set
pull off softner dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of o
... Read moreld cogs remove and replace with new, reassemble
Read less
Was this helpful?
Thank you for voting!
Dog ears worn down; upper agitator not moving
117 of 136 peoplefound this instruction helpful.
shawn from la jolla, CA
Easy
15 - 30 mins
Screw drivers, Socket set
Pulled off the dispenser. Used socket set to remove bolt. Removed entire agitator out of washer. Placed both feet on bottom of agitator and then pulled up on the upper agitator. It took some muscle due to the years of washer use. I used a flat-head screwdriver to weaken the plastic clips holding down the old bearing-driven cam. Once
... Read more I got the upper agitator off, the guts were easy to pull out. Then I just re-assembled with the 3 new parts (the Cam Driven, the Dog Ears, and the Bearing-Driven Cam).
My Orders
