My Orders
WTMC3321US (06) Bosch Dryer - Overview
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Longer Available
Door Hinge
Part #00491647
This door hinge is designed for use with dryers. The door hinge supports the door and allows the door to swing open and closed with ease. The hinge is made of metal, and it is easy to install, you will need a screwdriver. While holding the door, remove the four screws found on the cover plate of the door, this will allow you to remove the...Read more door from your appliance and access the hinge. Once the door is removed make sure you save the plastic bushings from the original hinge. You will then remove the two larger screws on the hinge, then slide the hinge straight up, and pull it out of the appliance. Place the plastic bushings on the new hinge, attach the hinge to the dryer, and reinstall the door.
Read less
No Longer Available
Lint Filter
Part #00436476
Fluff filters are also known as lint screens or lint traps. They are used in the assembly of dryers, they work to trap lint and other dryer debris from the exhaust air leaving the dryer. If the lint screen in your dryer is damaged, worn out, or lost this is the replacement part you need. Installation is simple, no tools are required, you ...Read morejust slide the replacement lint screen into place. This lint screen is white in color, and it is proximately 9.5 inches long and 10.5 inches wide.
Read less
$55.84
In Stock
Door Latch - White
Part #00491673
A door latch is also known as a door strike, this part is made of plastic and it is located on the inside of the dryer door. This part latches into the door catch, located on the front of your dryer, when the door is closed. The door latch and door catch work together to ensure the dryer door remains closed for the entire drying cycle. If...Read more your latch is broken or worn out the door on your dryer may not close properly, or may not close at all. This replacement part is approximately 1.25 inches long and 1 inch wide.
Read less
No Longer Available
Heating Element Assembly
Part #00436460
The heating element assembly found in dryers is what generates the heat required for the drying cycle. If your dryer is not heating, or not getting hot enough you will need to test and possibly replace your heating element. This assembly comes with both the heating element and the thermostat (NTC and protector). This assembly does not com...Read moree with the heat shield or the screws, those are sold separately. First you need to unplug your appliance, remove the rear panel, locate the heating element assembly, and carefully remove the wire leads to this part, as well as any screws holding it in place. To install the new assembly, simply attach it to the back of the dryer where the older element was, connect the wire leads, and replace the rear panel. Refer to model specific diagrams for exact location and placement.
Read less
No Longer Available
Drum Support Roller
Part #00422200
This wheel is used in the assembly of dryers, and it is commonly referred to as a drum support roller. Most dryers feature two of these support rollers. These rollers should be able to rotate smoothly on a shaft, they support the drum while also allowing it rotate freely and easily. If your dryer is making loud and high-pitched squeaking ...Read morenoises while it is operating that indicates there is a problem with the drum support rollers. Most often these rollers will need to be replaced if the bearing is damage or worn. This drum support roller is sold individually. Before you attempt dryer repairs make sure the appliance has been unplugged.
Read less
No Longer Available
Sleeve
Part #00422204
No Longer Available
High Limit Thermostat - 195 Degrees
Part #00422177
This high limit thermostat is a safety mechanism used in dryers. It is a temperature control switch that helps regulate the internal temperature of your gas or electric dryer. When the dryer temperature reaches a certain level, in this case 195 degrees, the high limit thermostat will break the circuit and prevent the appliance from sendin...Read moreg power to the heating element. This allows the internal temperature to cool down. When it reaches a certain level the thermostat will close the circuit and allow the appliance to start heating again. If your dryer will not heat at all, or if your dryer is getting too hot you will need to test the thermostats. Some models have more than one thermostat so be sure to test them all. Testing is simple, you use a multi-meter to ensure there is continuity, if there is no continuity at room temperature the high limit thermostat will need to be replaced.
Read less
$76.17
In Stock
LIMITER-TEMPERATURE
Part #00422272
This dryer high-limit thermostat is a safety component that helps protect the appliance from overheating by cutting power to the heating element when temperatures rise beyond safe operating limits. Built with a durable housing and equipped with a red manual reset button, it allows the thermostat to be reset after it trips, restoring norma...Read morel operation once the dryer has cooled. Replacing a faulty thermostat can prevent overheating, reduce fire risk, and extend the life of the dryer. Installation is generally straightforward for DIY repairs—just be sure to disconnect power before accessing and replacing the thermostat.
Read less
$37.22
In Stock
Dryer Thermistor
Part #10010119
Genuine OEM 00154166 Dryer Thermistor. This thermistor is for the the front of the dryer and monitors the temperature inside the dryer.
$29.67
In Stock
Drum Bearing
Part #00618931
This drum bearing supports smooth and stable drum rotation by reducing friction during operation. Designed for strength and longevity, it is commonly replaced when excessive noise, vibration, or resistance develops, helping restore quiet and balanced performance.
No Longer Available
No Longer Available
Temperature Sensor
Part #00422221
An NTC sensor, or thermistor helps regulate the internal temperature of your appliance. This part monitors the temperature and tells the control board what temperature your appliance is running at. If it is too hot the thermistor will tell the control board and it will stop sending heat into the appliance, and once it has cooled the contr...Read moreol board will then start heating again. If the sensor is not working properly your appliance might trip, you might notice it will not run, it will not start, it will turn itself off mid-cycle, or it may not heat properly. First you want to ensure there is no debris around the sensor, and that the NTC terminal connectors are not loose, it might be as simple as tightening the connection or cleaning the senor. If everything appears to be in working order and it is still not functioning properly you can test this part at room temperature with a multi-meter. Before repairing your appliance make sure it is unplugged.
Read less
Common Symptoms of the WTMC3321US
How this model fails, and the parts that fix it.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
no heat on the dryer
5 of 9 people
found this instruction helpful.
Did a quick on line search of the problem and found the Limiter Switch is normally the solution.....loaded the model number in the PartSelect data base and received the correct part the next day (standard shipping)! Replaced the part in about 45 mins and works perfectly. While I was ordering the Limiter switch I figured it was a good ti
... Read more
me to replace the drum light bulb as well. Again, perfect match. Great experience with PartSelect, will be sure to use them again!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!