This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a wash cycle. It is round in shape, and approximately 3 inches in diameter.
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pump, and it is responsible for transporting water out of the washing machine after a cycle. If the drain hose is kinked, damaged, or clogged, ...Read morethe washer will leak, or you may find standing water in the drum at the end of the cycle. Each drain hose comes with a metal clamp for fastening.
This water-level pressure switch in your wash monitors and regulates the water levels throughout the fill, wash, and rinse cycles. You will usually find it inside the control panel or near the tub. It ensures that the washer uses the appropriate amount of water for each cycle and load type. This genuine OEM assembly includes not only the switch itself but also the accompanying air dome tube.
This part is the replacement switch assembly for your top-load washer. It contains the switch mechanism and the connecting wire that hooks the door latch to the electrical system of the washer. The lid switch holds lets your washer know when the door is latched, so it can begin the wash cycle. If the lid switch is damaged, it will not all...Read moreow the washer to run properly. Be sure to disconnect the washer from the power and water sources before you begin this repair. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.
This inlet valve assembly in your washer controls the flow of hot and cold water into the machine, opening and closing as needed during the wash cycle to ensure the drum fills with water at the correct temperature. This valve is usually at the back of the washer where the water hoses connect to the machine. If the inlet valve is malfuncti...Read moreoning, you may notice issues such as the washer failing to fill with water, slow filling, or water entering the drum when the washer is off. This genuine OEM replacement part, sourced directly from the original manufacturer, is sold separately from supply hoses.
This drain pump assembly is responsible for removing water from your washer during the drain cycle. It is typically at the bottom of the washing machine and connected to the drain hose. If it is damaged, you may notice water not draining properly, unusual drain cycle noises, or a failure to move to the next cycle. This is a genuine replacement part sourced directly from the original manufacturer.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gerald - For model number WT7150CW
February 24, 2024
Does the Pulsator cap need to be removed in order to pick up extraneous items /debris?
the CL code fix is not specific enough.
Electric connect is ok; circuit breaker is ok..... what's going on???
Hello Gerald, thank you for your inquiry. According to our research, you may need to remove the pulsator cap if you want to clean the wash plate. The error code CL indicates that the control lock function is activated. Press and hold the extra rinse button for 3 seconds to deactivate this function. We hope that helps!
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Curt - For model number WT7150CW
February 18, 2025
Doesn't start when you push start button
Hi Curt,
Thank you for your question. If your washer will not start, we recommend checking the door lock assembly and the electronic control board. Before removing and checking these parts, unplug the washer from the electrical outlet. For the door lock assembly, you will need to check it for continuity with a multimeter on the Rx1 setting to see if it is operating normally. First check to see if you can operate it mechanically and to see if the levers and actuators are damaged or sticking. If you can operate lid lock assembly mechanically, test it with the multimeter. You should receive a reading of zero. If you get any other reading you will need to replace the lid lock assembly. When checking the electronic control board, check it for signs of damage, wear, scorching, or burn marks. If it shows any of these signs, you will need to replace the electronic control board. We hope this helps!
Hello! I am looking to replace the "Control Board" on this LG Washer. The control board is located at the top, rear of the machine, and inside of the Control Panel. The "touch" selections (to the right of the round center knob) no longer work when pressing to select a new washing function.
Hi Art, thank you for reaching out. The control board that you are looking for is part number PS16551768. It is the same part that will help you fix your issue. We hope this helps.
Hello Darin, thank you for reaching out to us. Check the cold water hose. Ensure the blue (cold) hose is connected securely and the faucet is fully open. Unhook the water hoses from the back of the washer. Clean the small screen filters inside the inlet valves, as they can become clogged with sediment. If you are using a specialized cycle, try switching to the Normal or Delicates cycle, which often allows cold-only selection. You can select the ColdWash option using the Options button. ColdWash is suitable for small loads and will increase the wash and rinse times by up to several minutes to maintain wash performance. We hope this information helps!
Was this helpful?
Thank you for voting!
Chad - For model number WT7150CW
December 6, 2023
My washer is not draining completely and I get an OE error code. I pulled the drain pump and it wasn’t clogged or blocked. I checked the hoses and there are no blockages. I reinstalled the pump, still didn’t work. I replaced the pump, still have the same problem. I reset the washer and I ran the diagnostic tests. The test gets stuck on T5 and then starts making a singing sound until I shut it off. The drum spins during diagnostics, but when I run it normally, the spin light will be on but the drum isn’t spinning. None of this makes any sense and any help is appreciated!
Hello Chad, thank you for your inquiry. According to our research, the OE error code indicates that the washer is experiencing a draining problem. As you have already replaced the drain pump and checked the hoses, we would recommend replacing the electronic control board, part number PS16551768, to fix the issue. It manages the washer's functions such as filling, washing, draining and spinning. We hope this solves your problem!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
leg broke off inside housing
5 of 12 peoplefound this instruction helpful.
thomas m from CARMICHAEL, CA
A Bit Difficult
Less than 15 mins
raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new
... Read more leg was a breeze.
Read less
Was this helpful?
Thank you for voting!
Drain hose had a pin hole leak external to washer
3 of 6 peoplefound this instruction helpful.
Terry from SIMI VALLEY, CA
Really Easy
30 - 60 mins
Screw drivers
Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting. The one difference from the existing install video online was that I didn't
... Read more have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).
Read less
Was this helpful?
Thank you for voting!
Detergent and Softner dispenser was not working peoperly
3 of 14 peoplefound this instruction helpful.
Roger from Bradenton, FL
Very Easy
Less than 15 mins
The old dispenser is removed by slightly raising the front as you pull it out of the housing slot. To install the new dispenser, keep the front slightly tilted up and insert the new dispenser into the housing alot
My Orders
