WT40XK1AC Honda Engine - Overview

This is a genuine replacement part which is supplied by the original equipment manufacturer. It is specially designed for use with Honda engines commonly installed on a variety of lawn and garden equipment. The purpose of it is to filter out dirt and other debris from the fuel that is supplied to the engine. It will over time become clogg...Read moreed and restrict the fuel from getting to the carburetor so it will need to be replaced. It is made of a high-quality plastic and is sold individually. Check the diagrams of your model for the correct installation of the new part.

This gasket is a genuine OEM replacement part designed to seal the area between the exhaust pipe and cylinder head. It has a length of 3 inches and a width of 1.5 inches. The gasket prevents exhaust gases produced during combustion from escaping through the connection points and prevents air from entering the exhaust system. A faulty gask...Read moreet will result in increased emission of harmful gases, overheating, increased noise, and overall lower engine performance. You will likely need to remove the exhaust pipe to access the gasket. Once the gasket is removed, clean the surface to ensure a good seal and place the new gasket in position. Reconnect the pipe and ensure all parts are secure.

This is a genuine OEM sourced replacement part which is specially supplied for use with Honda engines commonly installed on lawn and garden equipment. It is utilized to keep the oil in the tank, it includes a filler to check the oil level. It is a high-quality component which is made of durable plastic and it is sold individually.

The noise suppressor cap assembly, also known as the spark plug cap/boot is responsible for connecting the spark plug to the ignition coil, and helping to reduce the amount of noise created when running outdoor power equipment. This OEM replacement part includes a rubber cap with a metal contact inside. It is found at the end of the spark...Read more plug wire and has a threaded center shaft which allows you to easily screw it into position. Over time the metal contact may corrode, or the cap may dry out and crack or break. If your equipment is misfiring, running poorly, or has interference with other electronic equipment, the cap assembly likely needs to be replaced. To remove the old cap assembly, use your fingers or a set of pliers to carefully pull it off the end of the wire. Place the new cap assembly onto the end of the wire and fasten it securely. Please note this part is sold individually.

This replacement head cover gasket is specially designed for use on small Honda engines. It is used to provide an air tight seal for the head cover. Over time gaskets will tend to deteriorate, becoming brittle allowing for leaks. At this point it should be replaced. It is made out of a rubber material and it is sold individually. Replac...Read moreing this gasket is a quick and easy job. You would need a wrench to complete this repair. • Remove the head cover bolt • Separate head cover and the old gasket • Secure new gasket in place • Reattach the head cover

This is a genuine manufacturer-sourced replacement gasket which is specially designed for use with Honda engines commonly installed on lawn and garden equipment. It provides an air-tight seal for the muffler, over time it may wear out and begin to crack eventually requiring a replacement. Keep in mind this high-quality composite material gasket is sold individually.

This air cleaner element is an authentic manufacturer sourced replacement part. It is specially designed for Honda small engines. It is used to remove any contaminants from entering the engine. This filter is made out of pleated paper in a metal/plastic frame. Includes one filter element per order. Foam pre-filter is included. To replace...Read more this item no tool will be needed. • Remove the filter cover • Remove old filter element • Secure the new filter • Reattach the cover and test the unit

This replacement carburetor gasket is a high quality item that is sourced directly from original equipment manufacturer for use with Honda engines. This gasket is used to provide and air tight seal between the carburetor and the insulator. Please note this part is made from durable compound material and it is sold individually.

This is a genuine item that is supplied by the original equipment manufacturer for use with Honda that are commonly installed on a variety of lawn and garden equipment. It is a special component that opens and closes the valve. Over time it may wear out or get damaged eventually requiring a replacement. This high-quality arm-valve rocker ...Read moreis made of durable metal and is sold as an individual part. To ensure the proper repair procedure, refer to the appropriate diagrams for your model. A wrench set will be needed to take the cylinder head apart when replacing this arm-valve rocker.

This is an authentic Honda replacement part manufactured for use with small engines. The gasket is used to seal the connection between the crankcase and the crankcase cover. It is recommended to replace gaskets when servicing the engine to ensure proper seals when the cover is re-connected. The crankcase cover gasket is sold as an individual replacement part.

This is an authentic Honda replacement part that has been sourced from the original manufacturer to be used with small engines. The special gasket is used to seal the connection between the cylinder head and the body of the cylinder. It is recommended to replace gaskets when servicing the engine to ensure proper seals when the parts are reassembled. This item is available as an individual replacement part.