Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRT16QRCD0

WRT16QRCD0 Frigidaire Refrigerator - Overview

Get Parts and Repair Help for WRT16QRCD0

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRT16QRCD0, or you can search by name or part description. You can also find your part by where it is located on the WRT16QRCD0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRT16QRCD0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the WRT16QRCD0

[Viewing 5 of 5]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$13.80

Defrost Timer - 60Hz 120V

Defrost timers are part of the defrost circuit in your refrigerator and freezer. This timer cycles the defrost heater on and off. For every eight hours, the appliance timer will cy...

$2.98

Door Shelf End Cap - Left or Right Side

The door shelf end cap, or door bin support, secures the rack in a refrigerator or freezer door. Note that this fits on either the left or right hand side. If the end caps of your refrigerator or freezer are broken or cracked, or if your food retainer bar is not staying in place, then replacing the door support can solve this problem. No tools are needed for this repair project. To repair, first remove the end cap by pushing upward or downwards to slide it out the end of the rail. Next, replace with new end cap and line it up to clip it back onto the rail. It comes in white and measures about two inches high. Remember to wear gloves for safety.

$29.24

Run Capacitor

The run capacitor helps the compressor kick on and off while maintaining a constant temperature in your fridge and freezer. You may need to replace your run capacitor if your refri...

$60.20

Evaporator Fan Motor Kit

The evaporator fan motor kit is specifically made for your refrigerator to run the evaporator fan in your refrigerator. It is mounted on the center hub and has three lead wire terminals; its shaft has a diameter of 1/8 inches and is 1-1/4 inches long. The function of the evaporator fan motor is that it supplies air to the evaporator coils which then circulate cool air throughout your refrigerator, efficiently keeping your fresh food compartment cold. The tools you will need for this installation include a 1/4 inch nut driver, and a pair of wire strippers. Keep your hands protected during this repair by wearing work gloves.

$7.94

SOCKET

The light socket on your refrigerator houses the light bulb and connects it to the power source. If you notice that your refrigerator light does not come on when you open the door,...

$45.67

Door Shelf Retainer Bar - Cut to Fit

This is a white cut-to-fit door shelf retainer bar.

$15.70

Defrost Thermostat

This limiter thermostat cuts out when the temperature inside your refrigerator reaches 55 degrees Fahrenheit and kicks back in when the internal temperature drops to 20 degrees Fah...

$5.94

Crisper Drawer Cover Support

$7.53

Screw

This screw is sold individually.

$30.34

Door Handle with Mounting Block

This gray door handle can be used on either the fridge or freezer side. It comes with the mounting block, but does not include the screws.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Fridge got warm and freezer coils were frosted

  • Customer: Stephen from Warrington, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 303 of 358 people found this instruction helpful
Fridge is a side by side. The freezer is pretty narrow for a guy with wide shoulders.

Pulled plug.

Had to remove bottom drawers then used nut driver to remove screws closest to back wall in drawer runners. Once the back screws were removed the runners could be swung up or down out of way so back cover could be removed.

On... read more

Noisy fan

  • Customer: Jordan from Maumee, OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 134 of 151 people found this instruction helpful
1. Removed the 7 nuts using the nut driver from the freezer back panel inside the freezer.
2. Remove the back panel. The evaporator motor and fan are located above the coils.
3. Unplug the wiring harness.
4. Remove the two gold mounting screws holding the motor and fan in place.
5. Remove the motor and fan including the brackets.
6. ... read more

Clicking sound then within a minute clicking again, not cooling.

  • Customer: Melvin from Semmes, AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 74 of 86 people found this instruction helpful
UNPLUG REFRIGERATOR. Carefully remove relay from the side of the compressor. You shouldn't need a tool to do this, if it is hard you can gently pry the edge with a flat head screw driver just to loosen. Unplug white and red wires from relay, noting that the white wire goes in the hole with a #2 stamped beside it. Shake old relay, if it rattles like a baby r... read more