Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WRS6W1EW6

WRS6W1EW6 Westinghouse Refrigerator - Overview

Get Parts and Repair Help for WRS6W1EW6

If you know the refrigerator repair part you need, you can browse the list of all parts on the WRS6W1EW6, or you can search by name or part description. You can also find your part by where it is located on the WRS6W1EW6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for WRS6W1EW6 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$25.45

Door Bin

Door bins, also known as cantilever shelves, are storage bins located on the door of your refrigerator. Over time, a cold refrigerator can cause plastic to become fragile and break...

$4.15

Crisper Cover Support - Front

This crisper cover front support is used to keep the crisper shelf in place, and may need replacing if the door will not open or close. This part can be used for the front support and mounts to the inside cabinet wall. Replacing this part is an easy repair, but will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.

$32.61

Door Shelf

This white bin can also be used on the freezer/refrigerator door on some models. Sold individually.

$4.33

Crisper Support - Rear

Replacing the rear crisper support in your refrigerator is an easy job, but to complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. This part is made from plastic and mounts on the inside of the wall. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually.

$39.69

Door Bin

Gallon size. Sold individually.

$58.56

Upper Crisper Drawer Cover - Glass NOT Included

This cover holds up the top crisper drawer, and has drawer glides molded in it.

$8.41

Hinge Bearing

Sold individually. Also known as a short door closing cam.

$100.41

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice is automatically ejected and the process continues until the storage bucket is full. Your ice maker should be replaced if ice is not being generated, stored, dispensed, or the ice maker has been damaged. Replacing the ice maker is an easy job and only requires a 1/4 inch nut driver. Before you start this repair, make sure your refrigerator is unplugged. For help with this installation, check out the video below.

$14.48

Defrost Thermostat Kit

If you find that there is excessive frost in your freezer, or the freezer will not defrost, you may need to replace the defrost thermostat. The defrost thermostat kit comes with th...

$34.47

Evaporator Fan Motor Kit - 120V 60Hz

The evaporator fan motor circulates air through the food compartment for efficient cooling in refrigerators. The evaporator is located in the back of the freezer and it circulates the air over the refrigerator coils. The evaporator motor fan in your refrigerator should be replaced if the fridge section is too warm, the freezer section is too warm, orthe evaporator motor makes loud noises or stops working completely. The tools used for this repair are a 1/4 nut driver and wire strippers. *Please note: The motor has been updated by the manufacturer. Tip to detect if motor is not working, often if it fails it generates loud noises in the freezer area. For safety, make sure food is safely stored so it does not deteriorate while the power is off, and remember to unplug fridge.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

cracked, broken door bins

  • Customer: Beverly from Jackso, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 508 of 527 people found this instruction helpful
The new bins and I installed them in the door. Nice to have door space again. read more

freezer shelf broke

  • Customer: MONICA from LANCASTER, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 489 of 502 people found this instruction helpful
Easy slide it back in place read more

Shelf Cracked Because Excessive Weight Put On It

  • Customer: GEORGE from GARDEN GROVE, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 449 of 530 people found this instruction helpful
Slip the old one off and replace the new one with just snapping it in place! read more