This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
This is a crisper drawer shelf frame cover for models of refrigerator. This frame sits above the crisper drawer and allows a glass insert to be installed on top of it, for further food item storage and to properly seal the crisper drawer itself. If this frame is cracked, bent, or warped, it should be replaced immediately so it can properl...Read morey support the drawer that slides into it. This frame measures approximately 13 inches deep and 16 inches wide, and is made of durable white plastic. This frame is an OEM part, and does not include the glass insert that lays on top of it or the drawer that slides in below.
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a pr...Read moreotective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.
This authentic OEM black touch-up paint is specifically designed for repairing minor scratches, chips, or blemishes on your kitchen appliances. The bottle contains 16ml or 0.6oz of black paint and has an applicator brush under the cap, the same way a nail polish bottle is designed. Restoring these visible damages is important because crac...Read moreked or chipped surfaces can become a breeding ground for dirt and bacteria. If your existing bottle of paint has a thick or clumpy consistency, do not use it. Remember to shake the bottle before applying the paint to your appliance. Please keep in mind that this bottle is sold individually.
This Refrigerator Ice Maker Installation Kit connects the house water supply, to the refrigerator for ice maker and water dispenser operation. This kit includes 15-ft of copper tubing, (1) saddle valve, tape, and (1) tubing connector.
This refrigerator water filter housing is designed to securely hold the water filter in place while connecting the water supply lines to ensure proper filtration. It plays a critical role in maintaining the flow of clean, filtered water by protecting the filter from damage and ensuring it remains properly seated during operation. The hous...Read moreing supports the refrigerator’s water purification system by facilitating the removal of impurities and preserving water quality. Constructed from durable materials, it is built for long-term performance and reliability. Installation involves disconnecting the water supply, removing the old housing, and securing the new one using the existing fittings. Always verify your refrigerator’s model number to ensure compatibility before installation.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Paul - For model number WRS325SDHV08
May 2, 2024
My ice maker makes a noise(sounds like an old door that needs oiling)and i think the noise is after it dumps ice. Do you know what the sound could be and how to repair it ? DOM 2021
Hello Paul, thank you for the question. First, make sure you have good water pressure going to the refrigerator from your house and check water inlet valve is working fine. If it is fine, then it is possible that the ice maker is producing ice, and the ice gets stuck in the teeth of the ice maker. The motor of the ice maker will constantly try to push the ice out of the ice maker and into the ice bin. Your ice maker is either failing, and the rake has become misaligned, so you need a new ice maker, part number PS17216974. We hope this solves your problem!
A small plastic piece with three wings and a open area at the top fell off of my icemaker, where does it go?
Hello Robert, Thank you for your inquiry. We show the compatible ice maker as part# PS17216974 and the piece you are describing appears to be part of the end of the ice maker and you would need to replace the entire ice maker to fix it. We hope this helps you.
Hi Kathy, thank you for the question. Yes, you can order a replacement for the door shelf. The door shelf bin for the fresh food section is part number PS12578777, and the door shelf bar is part number PS11740306. The freezer door shelf trim is part number PS11740304. We hope that helps!
Hi Jody, thank you for your inquiry. Gently lift and lower the arm to see if it moves freely or if it feels stuck. Do not force it, as you could break it. Look for ice jams around the arm's pivot point, the ejector blades, or in the water fill tube at the back of the freezer. If you find ice, use a hair dryer on a low setting to melt it carefully. Glad to be of help!
Was this helpful?
Thank you for voting!
Prev
1
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Scratches in Surface
83 of 227 peoplefound this instruction helpful.
Michelle from Richardson, TX
Really Easy
Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Noise in Evaporator Fan section
6 of 17 peoplefound this instruction helpful.
Richard from HOLLISTER, CA
Really Easy
30 - 60 mins
Screw drivers
Opening up the Evaporator Fan section was a quick and easy job. After opening, I checked and removed the fan and looked at the grommet. The grommet on the fan was tight and secure and I could no longer hear the noise. I closed the opening. Something I had done while checking the fan grommet must have solved the problem. I have not hear th
... Read moree noise again!
Read less
Was this helpful?
Thank you for voting!
Plastic ice door hinges broke
1 of 2 peoplefound this instruction helpful.
Roy from HOUSTON, TX
Very Easy
More than 2 hours
Replacement part arrived via FedEx package with one hinge already broken off, unable to install. Still waiting on requested replacement.
My Orders
