Models
>
WPXH214F1WW
WPXH214F1WW General Electric Washer - Overview
Sections of the WPXH214F1WW
[Viewing 3 of 3]Manuals & Care Guides for WPXH214F1WW
Click to downloadKeep searches simple, eg. "belt" or "pump".
Shock Absorber Assembly
PartSelect #: PS270563
Manufacturer #: WH17X10001
This assembly comes with two shocks, four nuts, one leveling leg pin and instructions. These shock absorbers keep the washer from vigorous shaking during it's cycles.
No Longer Available
Drain Pump
PartSelect #: PS271336
Manufacturer #: WH23X10016
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
No Longer Available
Tub Spring with Sleeves
PartSelect #: PS268413
Manufacturer #: WH01X10022
Sold individually.
$105.85
Special Order
Rotary Knob
PartSelect #: PS783683
Manufacturer #: WH01X10200
Sold Individually. This knob can accept a D-shaped shaft.
No Longer Available
SCREW 8-18 X .31
PartSelect #: PS299875
Manufacturer #: WR2X9494
This screw is sold individually. Size 8 - 18 x 0.31
$35.41
Special Order
Water Inlet Valve
PartSelect #: PS270303
Manufacturer #: WH13X78
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$132.65
On Order
Inlet Hose - 2 pack
PartSelect #: PS2340055
Manufacturer #: WH41X10207
Includes 2 hoses that are 4 feet long, and 4 seals.
$23.79
In Stock
Drive Belt
PartSelect #: PS269367
Manufacturer #: WH08X10003
This drive belt contains 6 ribs.
No Longer Available
Questions And Answers for WPXH214F1WW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WPXH214F1WW
[Viewing 4 of 4]Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Spring & broken level-shock.
Disconected power & hoses. Removed 4 screws from two tabs at rear of top. Slid top fwd & up to remove. Removed two screws from lower front panel and removed panel. Removed back cover screws and back cover. Placed sling arround tub & lifted with 2"X4" on strap placing additional wood under sling supported by edges of machine. Removed one s
... Read more
cred and loosened mother that held spring hook in place. removed broken end and remainder of spring. hooked spring in hole in tub and raised spring upper hook on to support , re installed retainer. Went to lower side and removed plastic push bolts, by slipping a 1/2 " deep socker over front end and pulling from back with plirers.allign the holes in the new shock with the mount holes and nock them in place. remove sling from arround tub and re assemble all removed parts.
Read less
Parts Used:
-
STEWART from STOKESDALE, NC
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
17 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water pump becomes very noisy
This is the second time in the same 7 year old appliance. Remove the front bottom cover by removing 2 screws. Then remove the 2 screws holding the pump down. Then unclip the electrical wire from the pump and remove both hoses from the pump by squeezing the spring clamps with a pliers. Have a pan to collect the water that will drain fr
... Read more
om the lines. Take the new pump and install it in reverse order from above.
Read less
Parts Used:
-
Roger from Hudson, WI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
13 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken shock absorber
after pulling pins and installing new shocks, the washer still made loud ,disturbing sounds during use. Did some more investigating, turns out the inner bearings on the drum are bad. Apparently a problem with this model. Probably why the original shocks broke in the first place.
Parts Used:
-
leslie from circleville, OH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
10 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!