This 40w light bulb is a replacement bulb constructed of glass and metal. It is an easy-to-install electrical part which produces 40w of light. If the bulb won't light up then it may be broken and should be replaced. The bulb attaches directly to an appropriate light socket and has a small screw-in base. To access the exterior light bulb,...Read more you will need to remove the panel on the bottom of the microwave using a Phillips screwdriver. If your exterior light bulb has not been changed before, it is probably held in place with some silicone. You will need to cut away this silicone to remove the old bulb. If you cannot access the silicone with a utility knife, it can be removed using dental floss. Once the silicone is removed, simply unscrew the old bulb, and replace it with the new one. Be sure to disconnect the power to the microwave before you begin this repair. This light bulb measures about 1 1/8 inches. We do not recommend using a higher-wattage bulb for this appliance, and can only recommend this specific bulb. If fixing the bulb does not solve your microwave light issue, it's possibly a problem with the socket, which means the socket and/or board will need to be replaced. This can be a more dangerous repair, so consult your user manual or a technician before attempting.
This Charcoal Filter traps grease from your oven's exhaust to help prevent it from entering the vent, which could cause damage over time. If the exhaust fan on your microwave is not working, you may need to replace your charcoal filter. This charcoal filter is located within the intake grille of your microwave, which will need to be unscr...Read moreewed and opened to gain access to the filter. The manufacturer recommends that you change your charcoal filter every six months. This filter measures 5 inches by 5.375 inches by 0.375 inches. Be sure to measure your current filter to assure correct replacement. This product is sold individually. We recommend the use of gloves during installation to protect your hands from messy grease during your repair. You should also unplug your appliance at the electrical outlet or switch it off at the breaker. Using a Phillips screwdriver, unthread the screws securing the grill. Open the door and slide the grill to the left and lift it up to remove it. This will allow access to the filter so it can be either replaced or cleaned. Remember to insert the tabs of the grill into the frame and slide it to the right when you are done. To finish, shut the oven door and secure the grill with the screws.
This Grease Filter is constructed of Acrylonitrile Butadiene Styrene and is used to trap grease and help eliminate odors from the exhaust air while cooking. It attaches onto the exhaust and is rated as easy to install. The part is 12 15/16" x 5 3/4", and comes in silver. Refer to your make and model number to ensure this part is right fo...Read morer you. If the exhaust fan of your appliance is not working, this part is the most likely cause. This part is sold individually, and it should be noted that many microwaves require two filters, so you may need to replace both at the same time by purchasing two of this part. You should consider gloves during this simple repair (which requires no tools) to save yourself from getting greasy hands.
This a genuine OEM microwave cooking tray. It is also known as a microwave turntable or microwave plate. The function of the tray is to hold and rotate food items while the appliance is in use to ensure the food is being heated evenly. This cooking tray is made of transparent glass, and may need to be replaced if the tray is cracked or br...Read moreoken. A broken tray may prevent it from rotating if the three partial circles on the bottom of the tray will not connect to the turntable driver. This part is sold individually and is approximately 12 inches in diameter. It is recommended to check the drive coupling, or turntable driver, if tray is not turning.
This turntable ring in your microwave makes sure that your glass tray rotates smoothly. Located just above the internal floor, it supports the tray so that your food cooks evenly. A broken turntable ring will look warped or cracked. Additionally, the rotation may become uneven or wobbly. You should replace the ring when it is damaged, by ...Read moresimply taking out the old one from your appliance. Please note that this replacement part is sold individually and is a genuine OEM product, specifically designed for your microwave.
This mounting plate is sourced directly from the original manufacturer for use with microwaves. It is a metal plate designed to support a microwave by attaching the microwave to the wall studs. If the mounting plate wears down or becomes damaged, it will cause the microwave to tilt and become unstable, potentially damaging the appliance a...Read morend the wall it is attached to. Therefore, it is important to replace the plate promptly. First disconnect the microwave from the power source and locate the fasteners that hold the mounting plate. Detach the old plate and align the new one with the existing mounting holes. Secure the plate and check that the microwave is stable and unmoving.
This door interlock switch is a genuine replacement part designed for use in microwaves. It serves a critical safety function by preventing the microwave from operating when the door is open. Because proper operation of the microwave’s shielding and interlock system is essential for user safety, this part should be installed by a qualifie...Read mored service technician. After installation, the interlock switches and microwave shielding must be thoroughly tested to ensure the appliance meets safety standards.
This diode, or high voltage diode, is used in microwaves. It is an electrical current control device that ensures power flows in one direction and not the other way. If your microwave produces no heat, heats inconsistently, or gets noisy, replacing this part can be the solution. The tools needed for this replacement are a nutdriver, plier...Read mores, and screwdrivers. First remove the microwave cover, then remove the old part by disconnecting the small thermostat. Replace with the new diode. Remember to use the diagram provided by the manufacturer for more instructions.
If your microwave is not turning on it could be due to your fuse needing to be replaced. This part protects the microwave by shutting it off if there is an electrical surge. This fuse is just over an inch long, is metallic on both ends and ceramic in the middle. Before beginning this repair, unplug the appliance and wait a few minutes bef...Read moreore starting. Remove the outer cabinet which is held in place with two screws. You will then locate the power cord which will lead you to the fuse holder. Determine if the fuse has blown. Using an ohmmeter, you should be able to figure out if it has blown. A proper reading is zero ohms, if it reads as anything else then your fuse has in fact blown. Simply snap the old fuse out of place and place the new one in.
The light socket in your microwave houses the light bulb and connects it to the power source. The light bulb will screw into it, so the light bulb will be held in place. Be very careful when installing this part, and be sure to consult your manual before you begin this repair.
This is an authentic manufactured drive coupling for a microwave. It fits on the motor shaft to hold and rotate the glass turntable tray while the appliance is running. This part has a D-shaped insert for the motor shaft, and measures approximately 3 inches in diameter. You may need to replace this part if the microwave tray will not turn...Read more. No tools are required for this repair. It is recommended to check the support ring before ordering the drive coupling in case the wheels are broken. This part is also known as a turntable coupling or microwave turntable support.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeri - For model number WMH3205XVS2
October 26, 2022
Lights, clock, fan all works. But when I put time in to cook it runs for a split second and shuts off. What could be the problem?
Hello Jeri, thank you for your inquiry. According to our research, we would recommend checking the following parts to fix your issue: The door Switch, part number PS2338920, Door Interlock Switch, part number PS2361111, and Electronic Control Board, part number PS11754570. If you require assistance to place an order, please contact customer service. We hope that helps!
Hi George, thank you for reaching out. Based on the description that you have provided, we would recommend checking the diode, part number PS12584264, to fix the issue. We hope this solves your problem!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken glass turntable
403 of 420 peoplefound this instruction helpful.
Deborah from Baltimore, MD
Really Easy
Less than 15 mins
No repair- just replaced glass turntable. Right part I needed with first try
Was this helpful?
Thank you for voting!
light bult needed to be replaced
222 of 329 peoplefound this instruction helpful.
Deborah from Millersville, MD
Difficult
Less than 15 mins
Screw drivers
The nightmare was that this microwave is installed under the cabinet....in order to get to the light bulb I had to pull out my stove then squeeze into the space between the stove and counter....my old microwave light bult was much easier to change.....Shame on Whirlpool for making this so difficult.....must be a better way to cover the li
... Read moreght bulb so that we do not need a screwdriver to remove the door to get to the light bulb
Read less
Was this helpful?
Thank you for voting!
While attempting to get some from the cabinet above my microwave, a guest accidently pulled on the top grill vent and caused the plastic screw tap to crack and break leaving the grill vent hanging.
91 of 102 peoplefound this instruction helpful.
Susan K from Lacey, WA
Really Easy
Less than 15 mins
Screw drivers
I first went back Lowe's where I purchased my microwave in the hopes they would help in the ordering of the grill vent for my mircrowave. They advised me that they do not order parts and gave me a card of a company to call to order the part. I called the number on the card and was left on hold for 20 minutes then instead of helping me wit
... Read moreh the part I needed they proceeded to set up an appointment for someone in my local area to come to my home, order the part the later install. I knew that it was just 2 screws and bottom snaps to install and I didn't want to wait a week for someone to come to my home. I then went direct to the Whirlpool web-site and found "Partselect.com". I was unable to match my model# even though my microwave was only 13 months old but knew it was probably interchangeable with another so I then called "Partselect.com" and was just amazed at how helpful and knowledgeable the gentleman on the other end was. He found my part and was very patient in describing it to me to assure that it was the correct one. I was on the phone less than 10 minutes with him. The part came in 3 days and was the correct part:) It took me less than 5 minutes to gently snap the 2 bottom tabs in and screw in the left and right tabs on top. Thank you so much "Partselect.com" for making what could have been a timely and expensive part replacement be so very simply and inexpensive.
My Orders
