The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after...
$74.11
In Stock
Order within the next 10 hrs and your part ships today!
The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow...
$26.80
In Stock
Order within the next 10 hrs and your part ships today!
This magnetic door plunger, also known as the magnet holder, is built for your washer. When you order this part, you will receive the plastic housing and a spring that goes with it. The magnetic door ...
$24.28
In Stock
Order within the next 10 hrs and your part ships today!
This is a tub-to-pump drain hose for a front load washer. The hose features flexible bellows which allow it to expand and contract when necessary. It carries the water from the tub of the washer to th...
$41.72
In Stock
Order within the next 10 hrs and your part ships today!
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicate...
$41.72
In Stock
Order within the next 10 hrs and your part ships today!
This is a replacement detergent dispenser for your washer. It stores the detergent, and then dispenses it into the washer at the appropriate point in the wash cycle. If the detergent dispenser is brok...
$27.79
In Stock
Order within the next 10 hrs and your part ships today!
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
$108.19
In Stock
Order within the next 10 hrs and your part ships today!
This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your wa...
$26.76
In Stock
Order within the next 10 hrs and your part ships today!
This is a locking pin, and it works in conjunction with your washer. The part measures to be roughly 3 inches long, and less than an inch wide. The pin is cylindrical, off-white in color, and made ent...
This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before be...
$8.04
In Stock
Order within the next 10 hrs and your part ships today!
Order within the next 10 hrs and your part ships today!
Questions And Answers for WM8000HVA
Ask our experts a question about this model and we'll get back to you as soon as possible!
9 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Javier
January 8, 2020
I have a LG washer that had a oe error code.I've replace drain pump and clean the filter and still has the same error code oe
For model number WM8000HVA
Hello Javier and thank you for writing.
You should try a hard reset. Go to your breaker box, turn the breaker for your unit off, wait 5 minutes and turn the breaker back on. We hope this helps. Please contact us anytime if you require further assistance.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Javier
February 26, 2020
Need the inverter direct drive motor, what is the part number?
For model number WM8000HVA
Hello Javier, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS7321738. This model does not have a direct drive motor, it uses a Stator. We hope this helps.
I have replaced both the cold and hot water inlets and water level pressure switch, problem is the main wash valve is getting constant current only when washer is on and a wash cycle started. Even when test mode activated it will immediately activate main wash valve and will not stop filling until i power off the unit or unplug the main wash valve.
For model number WM8000HVA
Hello Shane, thank you for your question. Usually, if the water valve doesn't stop filling unless power is removed from the unit that is a valve issue. However, since you have replaced both valves, this issue is most likely caused by the control board. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Karey
December 14, 2023
We bought a home and the sellers included the washer and dryer. They must have kept the door of the washer closed, as the rubber ring is full of mold. Local appliance dealer told me
I should be able to replace the rubber ring. Your help is appreciated! I can’t wash clothes in it until this is replaced. It smells horrible. Thanks
For model number WM8000HVA
Hello Karey, thank you for asking. We would recommend replacing the door boot seal, part number PS6448330, to fix the issue. We have attached a relevant video that may not be of the same model but will help you in replacing the bood boot seal. We hope this helps!
I received a le error code repeatedly. I have unplugged the machine, put smaller loads. It does not work.Which part do i need to replace. thank you
For model number WM8000HVA
Hi Reshma, thank you for your question. There are a couple of parts that you may want to look into for being the issue. First would be your Rotor Position Sensor: PS3529186. Then you may have to actually take a look at your Rotor itself: PS3618454. Good luck with your repair.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam
... Read moree apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the
... Read more motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replac
... Read moree the magnet was $18. Instructions were included in the box. Part number on the drawing was A165. PS3618292 Magnetic Door Plunger