WM1388HW (ABWEPUS) LG Washer - Overview

The hot water inlet valve on your washing machine controls the water flow into the washer. This inlet valve has a standard hose fitting inlet and one water outlet. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the washer may leak, fill slowly, or not fill at all. To test yo...Read moreur valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 3 inches long x 3 inches wide.

The cold water inlet valve on your washing machine dispenses the cold water and bleach into the washer in the prewash cycle. This inlet valve has a standard hose fitting inlet and 2 water outlets facing 45 degrees to the left. The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, t...Read morehe washer may leak, fill slowly, or not fill at all. To test your valve, unplug the washer when the symptom occurs. If the washer continues to fill, then your inlet valve is defective. This part is approximately 4 inches long x 3 inches wide.

If you notice your washing machine is leaking water from the top of the transmission, it might be due to the gasket being damaged or worn down. When replacing your gasket, consider replacing your tub bearings at the same time. The gasket (or seal) is located at the back of the outer tub of your washing machine. To access this part you wil...Read morel need to pull the top off of the appliance by releasing the screws holding it in place. This part is sold individually, is black in color, and measures 3 inches in diameter.

The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, there could be an issue with the tub bearing. This genuine OEM replacement bearing has a 3-inch outer diameter, and is used to help the tub sp...Read morein smoothly and to stop the washing machine from shaking during the cycle. NOTE: This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly at the same time.

This hook locker, commonly referred to as a door lock strike is specially designed for LG washers. It is a small, metal plate that is attached to the washer door. When the door is closed it engages with the door lock mechanism to keep the door securely shut while the washer is running. If it is damaged, worn down, or corroded, it will be ...Read moreunable to engage with the locking mechanism and prevent your washer from closing or staying shut. You may notice that your washer will not start or stops running mid-cycle. You will need to replace the door strike to fix the washer.

This is a door lock switch, compatible with various models of LG washing machines. This door lock switch is designed to communicate to the control board when the door of the washer is closed, so the door can lock and allow the washing cycle to safely begin. If your washer is having difficulty locking before it begins its washing cycle, or...Read more if it has difficulty starting in general, you may need to replace this lock switch. This switch is made primarily of black, gray, and white plastic, and will require a screwdriver/drill, and a pair of needle nose pliers to replace. This door switch is a genuine OEM part that will require you to disassemble part of your washing machine to completely replace it.

This is a replacement shock absorber for your washer. The shock absorber is approximately 10 inches long and a little more than one inch wide. It is black and silver in color, and is sold individually. There are four shock absorbers on your washer. They support the tub and prevent it from shaking around. If your washer is shaking or makin...Read moreg a lot of noise during operation, you may need to replace the shock absorber. It is important to determine if you have one or more shock absorbers that need replacement before you begin the repair. This is an OEM part from the manufacturer.

This levelling leg is a genuine replacement part. It is used to help keep your washing machine stable and balanced. It helps support your appliance. It screws into the base of your washer, and you can thread it in or out to adjust the height. The foot on this leg is made of rubber, which helps with grip, stabilization, and vibration reduc...Read moretion. It is also hexagonal in shape, which allows you to more easily adjust it. This levelling leg features a locknut on the shaft which can be tightened against the bottom of your appliance, this will stop the leg from rotating while you are using your washer. This replacement is sold individually.

Also known as the water supply hose.