WL611101AJ Campbell Hausfeld Compressor - Overview

This replacement filter element is an authentic OEM item that is commonly utilized on Campbell Hausfeld air compressors. Its purpose is to filter out dust and debris from contaminating the engine with the air that goes into the carburetor. Please note this felt filter element is sold individually. Replacing it is a very simple task that does not require any tools.

It is an authentic manufacturer sourced replacement head gasket that is specially produced for Campbell Hausfeld air compressor pumps. The purpose of this gasket is to create an air-tight seal between the head and the cylinder case. Over time gaskets tend to get compressed and deteriorate eventually requiring replacement to maintain peak ...Read moreperformance. Please note this part is made from high quality composite material and it is sold individually.

This genuine OEM part is specially designed for Campbell Hausfeld air compressors. It is an important component which provides a tight seal between connected parts. If the part is worn, damaged or missing, this will provide an identical replacement for the original gasket that was installed on a new unit. To ensure the correct repair proc...Read moreedure, check the diagrams for your model. Note, this high-quality part is made of durable material and is sold as an individual item. A screwdriver and a wrench set will be needed to take apart and reassemble the equipment when performing this repair.

This replacement gasket is specially designed for use with Campbell Hausfeld air compressors. It is a high-quality component which is supplied by the original manufacturer and it is sold individually. The gasket provides an air-tight seal for the cylinder, over time gaskets tend to wear out and crack eventually requiring a replacement to ...Read moremaintain peak performance. Please make sure to check appropriate diagrams of your model for correct location and use of this gasket. It is an authentic item which is made of durable composite material and it is sold individually.

This is a manufacturer sourced replacement part designed for use with Campbell Hausfeld air compressors. The pressure switch tells your compressor when to stop and when to start. There are multiple reasons a pressure switch could be leaking air. If it is leaking air the pressure switch should be replaced for a compressor to operate proper...Read morely and safely. To complete this repair you would need: wrench set, nut driver set and a thread-sealing tape. • Shut off the electricity and drain the air tank • Remove the tank pressure gauge • Remove the pressure switch tube • Remove the pressure regulator assembly • Disconnect the wires • Remove the safety valve • Install the new pressure switch • Reinstall the safety valve • Connect the wires • Reinstall the pressure switch tube • Screw the pressure gauge onto the new pressure switch and tighten the gauge firmly • Test the air compressor

This is a genuine Campbell Hausfeld replacement part manufactured for use with air compressors. This special adapter is threaded to screw into the cylinder head on the pump, and connects the filter housing. This adapter requires two bolts to secure it to the filter housing, please note the adapter is sold individually.

This is an OEM part made for use on Campbell Hausfeld air compressors. This rubber foot attaches to the bottom of the tank. It does not need special tools to repair. Simply slide onto the tank's bar. It stabilizes positioning of the compressor while protecting surfaces below. Sold individually.

The head attaches to the discharge valve gasket. This is a genuine Campbell Hausfeld part sourced directly from the manufacturer for use in compressors and pumps. It is made out of metal and is sold individually. When replacing this item a wrench might be required during the installation process. This part may become broken and will need to be replaced.

This is a genuine Campbell Hausfeld replacement part manufactured for use with air compressors. The kit includes the valve plate, and all gaskets including the cylinder, and head gaskets. It is recommended to replace the gaskets when repairing the head, or cylinder to ensure a good seal when the parts are reassembled. This is a complete g...Read moreasket set, the set is sold individually, please note not all gaskets are available individually.

This is an authentic Campbell Hausfeld replacement part manufactured for use with air compressors. The filter gasket is used to for a seal at the connection between the air filter and cylinder head. It is recommended to replace gaskets when servicing the air compressor to ensure proper seals when the parts are reassembled. This filter gasket is sold as an individual replacement part.