This is the replacement water inlet pipe or water inlet valve for your washer. It is made of white plastic and is approximately 8.5 inches by 3 inches, with an opening diameter of approximately 2.5 in...
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
September 13, 2021
Water pump is leaking need replacement
For model number WHDVH626F0WW
Hello David, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS1766031. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
I had to replace the door gasket because there was a small piece that had torn away, which caused large amounts of water to leak when the load of laundry was too big. Smaller loads of laundry would just produce a little bit of water. Unsure of how to replace the gasket, I used a phillips screwdriver to pull the door and front panel off. I thought that this would be pretty simple, but I soon discovered that it wasn't as simple as removing several screws and pulling the pieces off. The door was easy, the bottom panel was easy, but the front panel was held in place by screws, plastic tabs, the front of the gasket (I'll explain later), and gravity by means of plastic supports. Trying to find and release the tabs, lifting the panel up and out was not self-explanatory. I finally figured it out, and it made changing the gasket out, a breeze. The gasket is held in by two diferent wire spring clamps/bands. One band holds the gasket to the outside of the tub, and the other band holds the gasket to the front panel. Before removing the front panel you must remove the first band which is cleverly hidden by the face of the rubber gasket. Just peel it back...it's in there. I was able to pull/pry this off with a screwdriver because I was not worried about damaging the old gasket. The second band had to be removed with either a 6mm/7mm wrench(I can't remember which) or a stubby phillips screwdriver. The stubby screwdriver is handy because of the proximity of the tubs counterweights. Once the final band is removed just peel the gasket away from the tub, after taking note of how it came off. Put the fully loosened band on the new gasket and fit the new gasket into place. It helped to have two sets of hands to work it around the tub, but probably not necessary. The wrench is necessary to properly tighten the band, because you cannot get enough torque on the stubby screwdriver.Once the gasket is in place you can re-install the front panel, and secure the front of the gasket to the panel. Install the band and it will secure itself by the tension of the spring. Put the door back on and you are ready to wash clothes.
Ordered new Parts. Removed old/worn parts. Found that the "hammering" from a loose pulley had worn and deformed the edges of the shaft where the flats are to accept new pulley. Gently filed the flats with the flat surface of the file and filed the hump on the shaft that the "hammering" created. Take extreme caution to not file surfaces too much, because new pulley will be loose and the next step is to replace the drum shaft.($$$$) Pulley did not fit 100% (Had some slop) but that was from material being worn away from "hammering" effect. Torqued with Torque wrench and added green 609 loctite compound - this is meant to help adhere and take up some loose fit in assemblies. - Drawback to Loctite is most have to be heated to 300 to 400 degrees to remove, or pulley will need to be cut off and ruined, I further repair/removal of pulley is necessary. This is an Easy Fix/Replacement of parts.... The hard part is filing the drum shaft surfaces to accept the new pulley, and getting the belt back on - Belt is tight but needs to be stretched on like putting a bike chain back on.
Washer now spins and sounds like a dream! - Good Luck!
Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test.