This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are most often used to light the inside of refrigerators and ranges. It features a standard socket base, which means you simply unscrew the burnt-o...Read moreut bulb and screw in the replacement. Depending on the appliance you may require a screwdriver or nut driver to access the light bulb. We recommend you wear work gloves while handling this replacement part. It is constructed of glass and metal and is sold individually. Depending on the appliance and location of the bulb within it, you may want to consider disconnecting power and using a flashlight for easier access to unscrewing and re-screwing in your bulb during this repair.
This is a leveling leg for your oven, range, or stove. The leveling legs on your oven allow your appliance to sit perfectly flat. The new one may be longer in length than your original, but will work the same. Install the new leveling leg, and test if you have it adjusted properly by putting the appliance on four legs. Adjust in or out a...Read mores required if your oven is rocking. It is recommended to check the other three leveling legs on your appliance in case they are also damaged or worn. The leveling leg measures 1.859", is all black in color, and is made entirely out of plastic. This leg may be shorter than the original but is the factory replacement. Longer leg is not available.
This oven rack is chrome in color and is approximately 24.76 inches wide by 15.78 inches deep. If your old oven rack is damaged, you should consider replacing it. Many of our customers have determined this repair to be very easy. You will not require any tools to complete it. To replace the oven rack, simply pull the old rack out, and rep...Read morelace it with the new one. Make sure to put the new rack back in the oven with the beveled edge in first. To keep your oven racks clean, we recommend that you pull them out before using the self-cleaning function on your oven.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
This gas range oven igniter is a flat-style component designed to initiate the heating process by glowing and igniting the gas for the bake burner. Essential for proper oven function, it ensures consistent and reliable heat for baking and broiling. Compatible with a wide range of models across brands such as Whirlpool, Maytag, KitchenAid,...Read more Kenmore, and others, this igniter addresses common issues including no heat, weak flame, uneven cooking, or delayed ignition. If the igniter glows but fails to light the burner, or if the oven doesn’t respond or heat evenly, replacement may be necessary. Before installation, disconnect power, shut off the gas supply, and verify compatibility with your appliance model. Handle the igniter carefully, as it is fragile.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
This broiler pan and roasting rack set is designed to help reduce mess while cooking by allowing grease to drain away from food. Its durable porcelain-coated construction stands up to high temperatures and makes cleanup simple. With approximate dimensions of 16 3/4 inches long, 12 3/4 inches wide, and 1 3/4 inches high, it offers a convenient size for everyday broiling and roasting.
This bottle of non-abrasive cooktop cleaner breaks down and gets rid of the hardest baked-on stains and residue without causing any harm to your appliance. The bottle is 10 oz and does not require a large amount of product to do the job. This cleaner is perfectly safe to use on any glass, ceramic, stainless steel, chrome, or porcelain coo...Read morektop surface. The cleaner is creamy in texture and provides a protective coat of silicone on smooth surfaces. To apply, use a gentle scrub, sponge, or rag and gently press in a circular motion until the stains are removed.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Todd - For model number WGG745S0FS02
January 7, 2025
I have a whirlpool wgg745sofs02 stove and the upper oven won't work when I try to "Bake". The broiler works but the Bake function does not work. I replaced the ignitor but it still does not Bake. When I turn it on and test for an electric current going to the ignitor I get no reading. So, maybe it's an issue getting power to the ignitor. What should I check next to see if I can get it to work?
Hi Todd, thank you for reaching out. Inspect the wiring connections between the control board and the ignitor. Look for any loose, damaged, or corroded wires that might be preventing power from reaching the ignitor. If they are fine, the issue could be with the oven control board, part number PS11759748. It is responsible for sending power to the ignitor. You may need to replace it to fix the issue. We hope this sorts out your problem!
I have a whirlpool stove and the large burner on the front of the stove top will not ignitete
Hello Freda, thank you for reaching out. The most common cause of the large front burner not igniting is a clogged burner port or a burner cap that is not seated correctly. Grease, food debris, or moisture can block the gas flow near the igniter, preventing the burner from lighting even though the igniter may be clicking. Remove the burner cap and head, clean the burner ports and igniter area thoroughly, and make sure the cap is properly aligned when reinstalled. If the burner still does not ignite after cleaning, the spark electrode may be faulty and should be replaced. The part number is PS12349231. We hope this information helps!
The lower oven door handle is loose. I understand the door has to be removed to repair it, but after releasing the 2 hinges the door won't lift off. It looks so easy in the videos, but it seems still connected.
Your advice?
Thanks,
James
Hello James, thank you for reaching out. After setting the oven door hinge in the unlocked position, partially close the door to engage the door latch locks. The door will stop at this point. Use two hands to remove the door. It may be necessary to gently shift the door from side to side. We hope this information helps!
Was this helpful?
Thank you for voting!
Scott - For model number 217-416-8402
June 26, 2026
need replacement knobs for a Whirlpool Gas Stove, model # WGG745SOFSO2, Serial # D73718260
Hi Scott, thank you for your inquiry. According to our research, the knob you are looking for is part number PS12348783. Glad to be of help!
Alfred - For model number WGG745S0FS02 Whirlpool gas stove
August 15, 2026
Looking for igniter for big burner on whirlpool gold. Series double oven gas stove
Hi Alfred, thank you for contacting us. The spark electrode for the surface burners is part number W11208293, and the oven igniter is part number W11596211. We hope that helps!
Was this helpful?
Thank you for voting!
Prev
1
2
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
mice had made nests in the insulation wrap in the range
129 of 211 peoplefound this instruction helpful.
Wendy from Red Hook, NY
Easy
More than 2 hours
Screw drivers
I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to
... Read more fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.
Read less
Was this helpful?
Thank you for voting!
Ignitor was bad on upper oven
77 of 88 peoplefound this instruction helpful.
David from Temple Terrace, FL
A Bit Difficult
1- 2 hours
Nutdriver, Pliers, Screw drivers
First I removed the lower tray and all parts covering the ignitor on the upper oven. 2. Then I removed the screws holding down the ignitor and flame distributor. 3. I then had to pull out the oven from the wall and remove the back panel to expose the wires connecting the ignitor. This required the removal of about six screws but they
... Read morewere fairly easy to get to. 4. I disconnected the ignitor from the back panel then went around to the front of the oven and pulled out the ignitor and all of the attached parts. 5. Here's the tricky part. The screws holding the ignitor in place had fused from the heat and then the threads stripped when I tried to remove them. I had to use a dremel tool and cutting wheel to carefully cut the screws off and then went to buy some replacement screws from the hardware store. 6. I replaced them with a nut and a bolt, to hopefully avoid the same problem for later replacement if necessary. 7. I then replaced everything the same way it came out and all is working like new!
Read less
Was this helpful?
Thank you for voting!
Socket Light had a bad thread
44 of 66 peoplefound this instruction helpful.
Edmund from Emporium, PA
Easy
15 - 30 mins
Pliers, Screw drivers
Socket Lite come with clips attached to the outside of the housing. After you unhook the 3 lead wires that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you snap in the new unit. Attach the 3 wire leads, put a oven bulb in the socket end, and the install the light cove
... Read morer
My Orders
