This is a manufacturer-approved replacement drain pump for your washing machine. To complete this repair you will need a 1/4 inch nut driver, 5/16ths nut driver, a flat blade screwdriver, and a pair of pliers. Make sure to disconnect power to the washer before beginning this repair.
Also known as a door boot seal.This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on th...Read moree appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
Affresh Washing Machine Cleaner includes three slow-dissolving tablets that help remove odor-causing residue from inside the washer. Suitable for all washer brands, including high-efficiency (HE) machines, the formula is also septic-safe. Place one tablet directly in the empty wash basket and run the Clean Washer cycle, or use a normal cycle with hot water. Use monthly or every 30 wash cycles for best results.
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens you will notice water leaking onto the floor. The tub-to-pump hose is found below the washer tub. To disconnect the hose, you will need to r...Read moreelease the clamps that hold it in place with a pair of pliers. When you replace the tub hose, you will need to transfer the ball, air chamber, and clamps from the old pump to the new one. To do this, you will need a set of wire cutters and a new zip tie to replace the one you will need to cut.
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature or amount of water needed.
This front-load washer door latch assembly is a vital safety and operational component designed to secure the door during the wash cycle. It ensures the machine only functions when the door is properly closed and locked, preventing accidental openings and potential water leaks. Constructed from high-strength ABS plastic and corrosion-resi...Read morestant metal, it offers long-term durability under frequent use. The latch automatically engages and disengages at appropriate points in the cycle, contributing to both user safety and machine efficiency. Replacement is recommended if the washer door fails to close or lock, or if the machine won’t start or complete its cycle. Installation should be performed with the washer unplugged, and model compatibility should be verified before purchase.
This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is found between the motor pulley and the drive pulley, and it connects the motor to the drive system. When the belt is running, it allows the...Read more basket or tub to spin. If the belt is stretched, worn, or broken, the tub will not turn. A warped belt can also cause the washer to be noisy while operating. This part is an authentic OEM part sourced directly from the manufacturer.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Charmaine - For model number WFW8400TW03
May 28, 2023
I need a motor control unit
Hi Charmaine, thank you for reaching out. The part you are looking for is the motor control board, part number PS11754006. We hope this helps!
Does not complete rinse and spin cycle and door remains locked?
Hi Tom, thank you for your question! Based on our research, the most likely cause is a faulty door latch assembly. If the latch fails to confirm that the door is securely locked throughout the cycle, the control board can stop before the rinse and spin cycle and keep the door locked as a safety precaution. Replacing the door latch assembly, part number PS11751211, can help restore normal cycle completion and proper door unlocking. We hope this solves your problem!
Pf error during the following cycles heavy duty & sanitary machine stops. Cancel then machine drains. Problem occurs again with pf error message. Please do not request turning circuit breaker off and then on to resolve.
A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. Touch and hold START to restart the dryer cycle or press POWER to clear the display.
-During a power outage, if there was an unexpected amount of power supply line "noise" that the control detected as an incorrect voltage amount, the control could display the PF Error Code. Also, if any keys were pressed before the 10 second delay interval on power up, this could cause the PF Error Code to appear.
-If your dryer was installed recently (within approximately 3 months), contact a qualified electrician to verify the electrical supply.
Was this helpful?
Thank you for voting!
Louis - For model number WFW8400TW03
January 19, 2020
Thanks for responding but not answering my question. You requested both the washer and dryer part and serial numbers. The model number for the washer is wfw8400tw03 and serial number hly3501930. The model number for the dryer wed8300sw2 and serial number my3579751. For the 3rd time, the question is the same. A pf error occurs during the following cycles heavy-duty and sanitary for the washer. Push cancel and the washer drains. The problem occurs again every time during the heavy-duty and sanitary cycles. Lights in the house do not dim or flash. What is the minimum voltage that the pf error occurs? This must be a control board problem for the washer. Do not understand why you are asking for the model number and serial number for the dryer since the problem is with the washer.
Hello and thank you for writing.
PF error occurs if the voltage is less than 93 Volts AC. We do ask for the model and serial numbers as our system find information based on these numbers. It is possible that our system showed the unit initially as a combo unit, that would explain why we asked for both model and serial numbers. We hope this helps. Please contact us anytime if you require further assistance.
Was this helpful?
Thank you for voting!
Louis - For model number WFW8400TW03
January 21, 2020
Ok, you answered the question on what supply voltage the pf error would occur. Thank you. Since it does not seem possible that the supply voltage ever was anywhere near 93 volts since the lights did not dim or flicker then the only conclusion must be a fault in the control board. Please confirm or indicate some other reason. Please provide how to replace the control board instructions and its cost. In addition provide names of local contractors in williamsburg va. Who could make repair.
Hello and thank you for writing.
There are 2 control boards in your unit that could cause the issue.
Control board PS11746709 and control board PS11755958, you would have to test both boards to establish which on is faulty, you could check for burn marks due to a short. Regretfully we do not have a list of contractors for your area. We hope this helps. Please contact us anytime if you require further assistance.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
F 21 error
376 of 426 peoplefound this instruction helpful.
Andrew from St.Louis, MO
Easy
15 - 30 mins
Screw drivers, Socket set
Removed the front panel unplugged The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
Was this helpful?
Thank you for voting!
Water leak from bottom of door.
201 of 224 peoplefound this instruction helpful.
Marty from Belfair, WA
Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers
I discovered water leaking from the bottom of the door on our Kenmore front load washer. I did a little self diagnosis from the internet and found that this seems to be a common problem for front load Kenmore washers and that the ususal suspect is the large rubbery bellows. I examined the bellows on my washer and although I didn't find
... Read moreanything wrong with it, I couldn't find any other likely causes. I shopped around and found PartSelect to be the cheapest for the replacement part. Removal is easy by removing the lower front panel with three small screws on the bottom front, then remove the very top panel and then the top front control panel and finally the door panel. the bellows are actually held in place with a spring loop on the outer and a screw tightener on the inner, both are fairly easy to remove and the bellows comes right off. For installation my best advice is to lube the bellows with a small amount of dishwashing soap in the groove that fits on the washer tub. This will help it slide into place and enables a small amount of sliding fine tuning once it is on. From there it is just a reverse of the removal.
Read less
Was this helpful?
Thank you for voting!
water pump failed
98 of 110 peoplefound this instruction helpful.
Kurt from Caliente, NV
Really Easy
15 - 30 mins
Nutdriver, Pliers
Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about
... Read more 15mins.
My Orders
