Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This washing machine cleaner includes three time-release tablets designed to remove odor-causing residues, grime, and buildup from high-efficiency and top-load washing machines. The tablets work by cl...
This washer door boot seal, also known as a door bellow, is a genuine replacement component designed for select front-load models from Whirlpool, Maytag, Amana, KitchenAid, and other affiliated brands...
The leveling leg locking nut is an OEM replacement fastener for use in dryers and washers. It has a head diameter of 3/8 inches and a thread pitch of 16 threads per inch. The nut secures the leveling ...
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
Ensure your Whirlpool washing machine functions at its best with our genuine OEM door strike. This essential component is designed to seamlessly fit with specific Whirlpool models. It efficiently acti...
Note: This part has been updated by the manufacturer. It may appear different but will still function the same as the original. The hose clamp is about 2 inches in diameter and made of stainless steel...
This Affresh Washing Machine Cleaner deep cleans to help remove the odor-causing residues and grime that daily loads leave behind. The time-release tablets are EPA Safer Choice certified, septic-safe ...
Introducing the Whirlpool Double Water Inlet Valve. This genuine OEM part is designed for optimal, reliable operation in a variety of washing machines. Not only is this valve perfect for Whirlpool mod...
This is an OEM boot seal retaining ring for various models of front-load washing machines. This retaining ring is used to clamp down and secure the inner boot, also known as a seal or gasket, of your...
$27.36
In Stock
Order now and your part arrives by Apr 23
Questions And Answers for WFW5620HW1
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brian
December 15, 2022
It runs for about 25 mins and shuts down.
About half cycle
For model number WFW5620HW1
Hello Brian, thank you for getting in touch. We have researched your model and would recommend checking the following parts to fix your issue: door latch, part number PS12711558, rotor, part number PS12711482, stator, part number PS12717590, and control board, part number PS12711818. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
Hi Wayne,
Thank you for your question. The LO FL error code indicates that the washer is not detecting the correct amount of water going into the washer. When this happens the door may be locked or the electronic control board is not responding. To resolve this, press the power button. The washer will start a drain routine where the pump will run continuously and will take 8-10 minutes to complete. Wait 10 minutes before using the washer. When using the washer, make sure the water is turned on before starting a wash cycle and make sure that the inlet and drain hoses are not kinked or clogged and that they are positioned correctly to allow proper water flow. Inspect the water inlet valve screens to make sure they are not clogged with sediment. If they are use a toothbrush to gently clean them. Also check the water inlet valve for continuity with a multimeter on the Rx1 setting to see that it is operating normally. You should receive a reading between 200 and 500 ohms. If you get any other reading, you will need a replacement water inlet valve. We hope this helps!
The washer door on this model when you shut it you push pull out power button it pops up in the led light up it says loc was a little cutest boy in the left bottom can't push play and start the washer wondering what i can do to remedy this problem
For model number WFW5620HW1
Hello Brock, Thank you for your inquiry. The LOC message means that the Control Lock is activated and the washer will not start until it has been deactivated. Try unplugging the washer for 10 minutes first to see if it resets the control. If not then you would have to deactivate it. On your model, it would either be the Power button or the Pause/Start button which you would need to press and hold for 10 seconds to deactivate the control lock feature. We hope this helps.
Did this question help you?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Replaced the Whirlpool washer water inlet valve. 1. Unplug washer 2. Close Hot and Cold water valves 3. Remove top cover of the machine by taking out 3 screws in the top back. Slide top back and remove. 4. Water Inlet Valve is located on the back left side, remove tubing using a nutdriver to loosen the hose clamps.
... Read more />5. Water Inlet Valve is removed by removing the screw in the back of the valve and turning the valve clockwise a little. Replace with the new one, connect hoses, put cover back on, open valves, plug it in. 6. Ran washer and Fabric Softener dispenser now works
We unplugged everything. Then we removed the screws from the back of the washer. Then we slid off the top of the washer. Next, we removed the bottom drawer of the washer. We then proceeded to remove all of the screws and took off the entire face of the washer until the bellow was completely exposed. We did have to detach the hose and door
... Read more clamp. We removed two metal clamps that held the seal in place. Once those were off we removed the entire old seal, replaced it with the new one, clamped it down, and reversed the steps to put everything back together. It was fairly simple.
