The hinge is mounted on the front of the washer, and the door is installed onto the hinge. When the hinge on a washing machine is broken or bent the door may not swing properly, and it may not close. If your door will not close your washer will not run, so you will need to replace the hinge on your appliance. Make sure you save the white ...Read moreplastic cap bushings from the old hinge, as you will need to install those on your new hinge, they are not included. This hinge is made of metal, and the screws you will need install it are included.
This valve is used in washers and it is known as the washer inlet valve. This specific valve is used to control the flow of cold water into your washing machine. If your washer is leaking, if it will not fill, if it is taking a long time to fill, or if it will only operate with hot water the dual inlet valve made be restricted or damaged....Read more If you find this valve is damaged or restricted it will need to be replaced. Before you replace this part, or any other part on your washer, make sure the water supply has been shutoff and ensure the appliance is unplugged.
This drain pump, also referred to as a drain pump motor assembly, is designed for use with front load washers. This pump is used to remove the water from your washing machine during the washing cycle. When the spin speed of the tub is maintained for a specific period of time the drain pump is then activated. If your washing machine will n...Read moreot drain you may have an issue with the drain pump, it may be damaged, clogged, or faulty. If you find an issue with your drain pump you will need to replace it. This drain pump assembly includes the drain pump motor, impeller, pump housing, and pump filter.
This valve is designed for use with washers. Inlet valves on washers are what control the flow of water into your appliance, this valve is used to control the flow of hot water into your washer. If your washer is leaking, if it is only washing in cold water, if it is not filling at all, or if it is filling slowly you will need to check th...Read moree inlet valves. If you find this inlet valve is clogged, restricted, or damaged in any way you will need to replace it. Before starting repair work you need to shut off the water supply, this helps prevent any flooding or mess while replacing the valve in your washer.
Front-loading washing machines use a suspension system to support the tub during the wash cycle. This suspension system is only designed to handle a certain amount of movement, so when you are transporting or moving the machine you will need shipping bolts to hold the tub in place. Using shipping bolts will help you limit any potential da...Read moremage that can be done to the suspension system during transport. This shipping bolt is comprised of three pieces, the bolt, the washer and the sleeve. You will need four of these bolts to hold the tub of your front load washer in place for moving.
This front-load washer door boot gasket is a flexible rubber seal designed to form a watertight barrier between the washer door and drum opening. It plays a critical role in preventing leaks, maintaining moisture control, and ensuring the door operates smoothly during wash cycles. Over time, gaskets can degrade due to repeated use, exposu...Read morere to moisture, and detergent buildup, leading to cracks or water seepage. This genuine OEM replacement is engineered to meet manufacturer specifications and is compatible with select front-load washers. The complete kit may include the gasket, plastic door frame, clamps, and installation instructions. Always verify your appliance’s model number before installation. Proper installation helps restore the washer’s efficiency and prevents further water damage.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Al - For model number WFMC3200UC-01
November 26, 2021
We have odour and wonder if there is a filter. There is a circular plate at the front bottom right but doesn’t seem to come off. Thanks
Hello Al, Thank you for your inquiry. We have researched the model number you have provided and there is a filter in the drain pump assembly that you can take out and clean. The smell can come from the water inlet, the door boot seal (or bellow) or blocked drain system . You can trying using a washer cleaning product or sprinkle baking soda in the drum and put white vinegar in the detergent tray and run a cleaning cycling or regular wash with hot water. To clean the door boot seal, undo the clamps and remove the seal and clean it with hot soapy water. We have included a link to our installation video for a similar part to give you a general idea of how to remove the door boot seal. We hope this helps.
Hi Normand, we have a video here, sadly we have no french version: https://www.youtube.com/watch?v=OD4OTAtOC6I. Thank you for your question and good luck with your repair!
The top part of the hinge assembly that attaches to the door on my clothes washer is broken . I was wondering if this part is still available for this model and if so where I could purchase one . Please
Hello Bren, thank you for for your inquiry. We found the Door hinge Cover PS8722546 to be discontinued but the Door Hinge is PS8731238. Have a good day.
Quick wash setting does not let water in tub, not the other settings do. What is the problem and what do I replace
Hello Carol, thank you for reaching out. The issue could be with the cold water inlet valve. It has two independent coils, so one can fail and block water on the Quick Wash setting while the other works fine. You may need to replace it. The part number is PS8713229. We hope this helps!
Will not drain completely; most of the water drains out, but clothes full of water.
Hi Lydia, thank you for reaching out. The drain pump is most likely causing this issue. The internal pump motor can develop electrical or mechanical wear over time, allowing it to handle lighter water flow but losing the torque needed to move a full load of water through the drain hose and up into the household standpipe. This can leave most of the water drained while some remains in the tub, resulting in waterlogged clothes. Replacing the drain pump, part number 00436440, can help restore proper drainage and remove the remaining water from the washer. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Prev
1
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hinge bracket snapped off
16 of 21 peoplefound this instruction helpful.
James from ALEXANDRIA, VA
Easy
15 - 30 mins
Screw drivers
Removed washing machine door. Then removed old hinge. Replaced with the new hinge. Replaced door. SPECIAL NOTE: Do not lose white plastic rings that cover hinge nipples on washer. The replacement part does not come with these 4 pieces.
Was this helpful?
Thank you for voting!
We got E13 code, meaning "something" is in the pump--needs clean out. We cleaned out and it worked only once more:( A small plastic peice was cracked and let water and "junk" into the pump--a total loss.
13 of 16 peoplefound this instruction helpful.
Sheriann from GLENN, CA
A Bit Difficult
30 - 60 mins
Screw drivers
My husband took off the back of the washer and disconnected the hose that connected the pump to the main drum. He has strong fingers--did it that way--but really you need a pillars. After putting it all back together we got another weird code--E29 and the door wouldn't lock. But after turning everything off and waiting 30 minutes, the
... Read moregenius machine just suddenly reset itself and started working correctly. No problems since and we've done about 30 loads since then. While on the phone with Bosch, trying to learn how to clear the new code, I heard only, "We only give information to certified repairmen and home repairs are definitely not covered by the warranty." Who cares? I'm now a satisfied mom who is actually washing clothes after only two days waiting for shipping--IF I could get any repairman to my house this month I'd be surprised and not for cheaper than the price of a new washer! Thank you for your great parts:)
Read less
Was this helpful?
Thank you for voting!
The inlet valve on my washer was leaking
7 of 7 peoplefound this instruction helpful.
Donna from HUNTERSVILLE, NC
Really Easy
Less than 15 mins
Pliers, Screw drivers
Turned off the water to the washer. Took the top off of the washer. Used pliers to loosen the rings holding the hoses to the valve. After the hoses were removed from the valve I popped out the old inlet valve. I put the new inlet valve in place and put the hoses and rings back on. Secured the top of washer back on the washer turned the wa
... Read moreter back on. No leak present.
My Orders
