This washer door lock and switch assembly is a critical safety and control component for front-loading washing machines. It secures the door during wash and spin cycles, preventing accidental opening and ensuring the appliance operates only when properly latched. The integrated interlock switch communicates with the washer’s control syste...Read morem to verify door status, helping prevent cycle interruptions and operational errors. This model features a four-lead switch for precise functionality and is compatible with a wide range of front-load washers. Replacing this part can resolve issues such as a door that won’t close, won’t open, or won’t lock, as well as a washer that fails to start. Installation should be performed with the appliance unplugged and may require basic tools.
This door boot (part number DC64-00802A) is for washers. Door boot DC64-00802A forms a seal between the wash tub and the door, preventing leaks. Unplug the washer before installing this part. Wear work gloves to protect your hands.
This is a door lever strike for Samsung washing machines. This part is used to latch and hold the washer door to the washer door frame when it is closed. If the door strike for your washer is currently broken, damaged, or not properly catching, this must be replaced for your door to close securely. This door strike is a genuine OEM part m...Read moreade of plastic and is sold individually, meaning it will need to be installed with the 2 screws securing the current door strike.
This is a shipping bolt designed by and for Samsung washing machines. This shipping bolt is installed in the back of the washer before transporting it to securely fasten the tub of the washer so it does not move. This bolt measures approximately 6 inches long and is normally installed with multiple other bolts. To install this bolt, remov...Read moree the protective cap on the back of your washer and carefully screw it into the appropriate hole. Depending on your model, you may need other shipping bolts of different lengths, so check your user manual for further information. This OEM shipping bolt is sold individually, so consider how many you need before ordering.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
front load washer latch replacement
198 of 242 peoplefound this instruction helpful.
James from Vilonia, AR
A Bit Difficult
Less than 15 mins
Nutdriver, Screw drivers
1. remove the three screws from the top backside of the top panel 2. push the top panel to the rear 1/8 to 1/4 inch 3. lift/rotate top panel from rear to front, set aside. 4. remove the three wire connectors from latch. 5. use #15 Torx to remove the three screws from the latch. 6. remove and replace part using to
... Read morep opening. 7. reverse order to finish.
Read less
Was this helpful?
Thank you for voting!
Door lock was in the locked position and door could not close
67 of 76 peoplefound this instruction helpful.
Suryakant from Cortlandt Manor, NY
Easy
15 - 30 mins
Screw drivers
I bought a new door lock for 132 dollars (item number PS2037196).
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the bac
... Read morek of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that. (there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that. You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble. (Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
Thats it.
Read less
Was this helpful?
Thank you for voting!
The Washer became unbalanced and broke the latch on door
32 of 44 peoplefound this instruction helpful.
Glenn from Las Vegaas, NM
A Bit Difficult
1- 2 hours
Nutdriver, Screw drivers
Had to take the entire front of the washer off to replace the door latch.