All Installation Instructions for Jenn-Air Wall Oven W211

oven would not heat

Checked the element to see if it was open or no
resistance, it was open
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

Parts Used:

Bake Element

Dane from Evansville, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replaced the heating element

It would have been a very easy job if the one wire had not fallen inot the back. I could not reach it and fried to figure out how to get in the back to no avail. Finally I took a piece of wire coat hangerm and bent it and then fished it out. The packing around the hole compressed while I was trying to get the wire and I thought I wpuld have to replace it, but overnight it resumed its original size. It should have probably taken less than thirty minutes.

Parts Used:

Bake Element

Paul from Newark, DE
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Very Easy Repair

The door came off easily after I removed the two hinge covers that are attached to the oven. Taking the door off can be done with one person but ideally two.

The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).

After that, re-assemble the door and drop in place. It was a snap.

FYI...the shipping was ultra fast and the price was great.

No issues whatsover with the entire process.

Parts Used:

Door Hinge

Donald from Edmond, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven light burnt out

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Parts Used:

Light Bulb - 40W

William from Schwenksville, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

3 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burned oven bulb

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Parts Used:

Light Bulb - 40W

Ivanka from Atlantra, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

3 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

missing clock knob

placed knob on clock shaft with my fingers

Parts Used:

Clock Knob

Jimmie from Hampton, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven temp would not get above 200

downloaded instructions from your website on how the part went in the oven, ordered part, and installed when it got here. shut off the breaker (found out it was mis-marked in my breaker box!) undid two screws, pulled off two clamps reinstalled and we were baking by dinner!
thank you!

Parts Used:

Bake Element

eleanor from baton rouge, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bulb Replacement

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Parts Used:

Light Bulb - 40W

Judith from Phoenix, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

element was burned out

remove old one and installed new one quick and easy thank you

Parts Used:

Bake Element

Gary from chardon, OH
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

would not heat up

my wife removed two screws and removed clips with pliers. We ordered part (2 days) it was fast. Installed in less than 5 min. and I only have one arm. We tried to find part locally but with no model # the parts houses could not find it. We found it on your site in less than 10 min. Your graphs and photos made it super easy. Will pass along your site to others. Thanks for being so helpful.

Parts Used:

Bake Element