VX831205 (2004) Campbell Hausfeld Compressor - Overview

Designed for use in compressors, this genuine replacement part is used to provide a seal and prevent leaks. It is red, made of rubber, is not part of a kit or assembly, and is sold individually. When this part is worn, you will notice leaks from your machine, and it will need to be replaced. As with most rubber seals, this part is known...Read more to wear with regular use of your compressor, and will no longer be able to properly seal when it needs to be replaced. It is found at the bottom of the air tank, and you will need a wrench to complete this repair. Customers rate this repair as Easy.

The purpose of a gauge is to register the pressure readings inside the tank. This replacement gauge is sourced directly from original equipment manufacturer for use with Campbell Hausfeld air compressors. The dial reads 0-250 PSI. Please note this gauge has a durable metal body and it is sold individually. You should only need a wrench and a thread-sealing tape to complete this repair.

This is a genuine Campbell Hausfeld replacement part that has been sourced from the original manufacturer to be used with air compressors. The flywheel attaches to the pump's crankshaft and is used to rotate with the belt that is linked to the motor's pulley. This item is priced as a single replacement part.

This OEM Check Valve is an exact replacement for certain air compressors. The purpose of this part is to allow pressurized air into the tank and stop it from flowing back into the pump. It is made of metal, is gold, is not part of a kit or assembly, and is sold individually. When the check valve is defective, the compressor will funcyio...Read moren normally until the tank fills with air. At that point, the pump will try to restart, but the engine will only produce a humming noise. Similarly, if the tank is full of air, the motor will make a humming noise without engaging. This part is located on the tank to the discharge tube and will need to be replaced if broken or worn. You will need a wrench set and a socket set to complete this repair. Customers rate this repair as Easy.

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

It is a genuine manufacturer-supplied item that is made for Campbell Hausfeld air compressors. O-rings are commonly utilized to provide an air-tight seal between connected components. Unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement. Check the diagrams for your model to ensur...Read moree the correct repair procedure. A screwdriver and a wrench set might be needed to replace this inspection port o-ring.

This ASME safety valve is constructed of high-qualty metal, and is made for use with many air compressor models. Fastened to the manifold, the safety valve diminishes air pressure when the pump is not shut off at the proper setting. This important component is sold individually. A screwdriver, adjustable wrench and a pair of pliers are of...Read moreten necessary for the removal and replacement. Please refer to the specific manual for additional repair information.

It is a genuine OEM part that is made for Campbell Hausfeld air compressors. The unloader valve is an important component which allows a user to safely drain the air from the tank. Unfortunately, over time it may wear out or get damaged eventually requiring a replacement to ensure your unit operates properly. Note, this high-quality unloa...Read moreder includes multiple parts however it is sold as an individual component. Check the owner\\\'s manual and the diagrams of your model to ensure the correct installation and application. You will need a wrench set and pliers to perform this repair.

This handle is an original replacement part supplied by the manufacturer. It is commonly used in Campbell Hausfeld air compressors. It is compatible with over 150 models. This handle is attached to the top of the tank (part AR040500CG). A screwdriver is needed to remove and replace the screws that secure this part.

This part is an OEM from Campbell Hausfeld. The axle bolt is compatible with many air compressors, and is sold individually. The metal bolt fastens the wheel to the base of the tank, providing movement to the device. A wrench and pliers are needed for the removal and replacement.

This is an authentic replacement part sourced directly from the manufacturer. The wheel is commonly found in Campbell Hausfeld air compressors. This part is made of high-quality plastic and rubber, and is placed on the sides of the tank to make the machine easier to relocate. You will require a wrench when replacing this item. The wheel is provided as an individual replacement part.