VX400200 Campbell Hausfeld Compressor - Overview

Designed for use in compressors, this genuine replacement part is used to provide a seal and prevent leaks. It is red, made of rubber, is not part of a kit or assembly, and is sold individually. When this part is worn, you will notice leaks from your machine, and it will need to be replaced. As with most rubber seals, this part is known...Read more to wear with regular use of your compressor, and will no longer be able to properly seal when it needs to be replaced. It is found at the bottom of the air tank, and you will need a wrench to complete this repair. Customers rate this repair as Easy.

The purpose of a gauge is to register the pressure readings inside the tank. This replacement gauge is sourced directly from original equipment manufacturer for use with Campbell Hausfeld air compressors. The dial reads 0-250 PSI. Please note this gauge has a durable metal body and it is sold individually. You should only need a wrench and a thread-sealing tape to complete this repair.

This is an original manufacturer approved replacement air filter assembly which is specially designed for use with Campbell Hausfeld air compressors. Its purpose is to ensure the air that goes into the engine is free of dust and other harmful contaminants, over time it may get dirty and clogged eventually requiring replacement to maintain...Read more good air flow. This part consists of a durable metal housing with a pleated paper filter element.

This is a genuine OEM sourced replacement part used on Campbell Hausfeld air compressors. Its purpose is to filter out dust and debris from contaminating the engine. This filter is made out of paper and metal. This item is sold individually. To replace this you would need a wrench to remove the air cleaner cover.

This is a genuine OEM sourced replacement part designed for use with air compressors. This breather acts as a valve for the fuel tank, it allows for the air to enter the fuel tank but it won't allow fuel or fuel emissions to leave the tank. It is made out of plastic and it is sold individually. No special tools are needed to replace this Breather Assembly, simply screw it in the opening on the crankcase.

This Power Cord and Plug Assembly is an OEM sourced part for air compressors. It is wired to the electric motor in order to provide power from a standard outlet. This part is black, consists of a metal wire in a rubber insulated cable, and is sold individually. Depending on how worn it is, your compressor may no longer get power or may ...Read morehave sparks coming from it when it needs to be replaced. If you notice any visible damage such as exposed wires, cracks, or frays, it should be replaced. You will need a screwdriver, pliers, and a wrench to complete this repair. Customers rate this repair as Easy.

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

This heavy-duty pressure switch helps regulate when an air compressor starts and stops by controlling pressure between roughly 100 PSI and 135 PSI. Built with a four-port design and a convenient unloader valve, it replaces a worn or faulty switch that may cause the compressor to run inconsistently, leak air, or fail to shut off properly. ...Read moreDesigned for select compressor models, it offers a reliable, easy-to-install solution for restoring safe, consistent pressure control.

This is an authentic replacement part sourced directly from the manufacturer. The wheel is commonly found in Campbell Hausfeld air compressors. This part is made of high-quality plastic and rubber, and is placed on the sides of the tank to make the machine easier to relocate. You will require a wrench when replacing this item. The wheel is provided as an individual replacement part.

This is an authentic OEM part. The 1/2 compression sleeve is compatible with many air compressor machines. With the compression nut, this item helps to secure the exhaust tube to the front shroud. An adjustable wrench is necessary for the replacement. The compression sleeve is sold individually.