VT761000AJ Campbell Hausfeld Compressor - Overview

This OEM Check Valve is an exact replacement for certain air compressors. The purpose of this part is to allow pressurized air into the tank and stop it from flowing back into the pump. It is made of metal, is gold, is not part of a kit or assembly, and is sold individually. When the check valve is defective, the compressor will funcyio...Read moren normally until the tank fills with air. At that point, the pump will try to restart, but the engine will only produce a humming noise. Similarly, if the tank is full of air, the motor will make a humming noise without engaging. This part is located on the tank to the discharge tube and will need to be replaced if broken or worn. You will need a wrench set and a socket set to complete this repair. Customers rate this repair as Easy.

This OEM part is sourced directly from the manufacturer and is an exact replacement for various air compressors. This Assembly includes the valve plate and two cardboard composite gaskets. It is gray in color, and its primary purpose is to provide a seal between the cylinder head and crankcase. This part will need to be replaced if you h...Read moreear air leaking, the tank takes a long time to fill, if it is worn or damaged, or if you removed the cylinder head from the crankcase for other repairs as gaskets are a one-time use part. You will need a screwdriver, a socket set, a wrench set, and a torque wrench to complete this repair. Customers rate this repair as Easy.

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

This is an authentic OEM approved replacement part that is commonly utilized on Campbell Hausfeld air compressors. Its purpose is to ensure the air that goes into the unit is free of dust and other harmful contaminants. Over time the filter will get dirty and clogged restricting the air flow, inspect it periodically and replace filter as ...Read moreneeded to maintain peak performance. Please note this durable pleated paper filter is sold individually.

This genuine replacement pressure switch is specially designed for Campbell Hausfeld air compressors. It is sourced directly from the original equipment manufacturer and it is sold individually. The purpose of a pressure switch is to control when the compressor should start and stop building up pressure. The default setting of this pressu...Read morere switch is 100psi on and 135psi off. Please note this high-quality item is sold individually.

This is an authentic OEM part. The 1/2 compression sleeve is compatible with many air compressor machines. With the compression nut, this item helps to secure the exhaust tube to the front shroud. An adjustable wrench is necessary for the replacement. The compression sleeve is sold individually.

This is a genuine Campbell Hausfeld replacement drain valve, sold individually. When using an air compressor, moisture naturally condenses inside the tank. If this water is left sitting for too long, it can lead to internal rust and damage. The drain valve allows you to release this built-up moisture easily. It's especially important to d...Read morerain your tank after each use—particularly if you tend to leave air in the tank for extended periods. Regular draining helps extend the life of your compressor and maintain its performance. Be sure to open the valve regularly to prevent water buildup and potential tank corrosion.

1/4

It is an identical replacement for a missing or a faulty cylinder head that was installed on a new unit. Please make sure to check appropriate diagrams for the correct location and use of this hardware. This authentic component is supplied directly from the original equipment manufacturer for Campbell Hausfeld air compressors. One durable...Read more metal cylinder head and the fasteners to secure it are included. A wrench set will be needed to perform this repair.

This genuine OEM replacement nipple is designed for use in air compressors, serving as a critical connector between the pressure switch, the tank, and the regulator. A damaged or corroded nipple can lead to air leaks and inconsistent pressure, affecting overall performance. To check for leaks, apply soapy water to the fittings around the ...Read morepressure switch and watch for bubbles. If replacement is necessary, the process typically involves disassembling the pressure switch. Begin by draining the tank using the valve at the bottom, then remove the coupler from the regulator and unthread the nipple. Access the wire connections by removing the pressure switch shroud, and carefully note the position of each wire before disconnecting them—starting with the motor wire, followed by the cord wires and ground wires. Remove the strain relief, pressure gauge, and the airline connecting the check valve to the switch. Finally, unthread the pressure switch from the tank nipple and remove the nipple itself. When reassembling, it is recommended to use thread tape to ensure a proper seal. This replacement part is sold individually.

It is an authentic replacement item that is specially supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the push-in fitting for the check valve which is sold separately. It is a quick-connect style fitting that is designed to accommodate for 1/4

This is a genuine OEM part. The compression connector assembly is made by Campbell Hausfeld, and is compatible with many air compressor devices. The metal component secures the manifold to the compressor tank. This item is sold individually. A screwdriver and a pair of pliers are often helpful in making the replacement.