VT640301 Campbell Hausfeld Compressor - Overview

This is a genuine Campbell Hausfeld replacement part that has been sourced from the original manufacturer to be used with air compressors. The flywheel attaches to the pump's crankshaft and is used to rotate with the belt that is linked to the motor's pulley. This item is priced as a single replacement part.

This is a genuine manufacturer sourced replacement regulator. It is specially designed for Campbell Hausfeld air compressors. This part adjusts the pressure of the air coming from the tank to the desired level. Please note, this only includes the metal regulator and the plastic knob. The valves, gauges and the pressure switch are all sold...Read more separately. To complete this repair you would need an a screwdriver, pliers and a set of wrenches. • First make sure to unplug the compressor • Drain the air from the tank • Disconnect all the valves and gauges from the regulator • Remove the old regulator • Secure the new regulator assembly • Reassemble and test the new regulator

This item is an original part from Campbell Hausfeld for use in compressors. The pressure switch unloader valve connects to the pressure switch. A wrench set and a screwdriver may be necessary during the installation of this part. The valve is made out of metal and will need to be replaced if it breaks since it can cause air leaks. This item is priced individually but also includes three nuts.

This is an authentic replacement part manufactured for use with air compressors. The switch is used to turn the pump motor on when the pressure in the tank drops below the desired pressure setting, and to turn it off when the pressure reaches the desired amount. This switch is sold as an individual replacement part, please see model diagram for associative parts.

This is a genuine Campbell Hausfeld replacement drain valve, sold individually. When using an air compressor, moisture naturally condenses inside the tank. If this water is left sitting for too long, it can lead to internal rust and damage. The drain valve allows you to release this built-up moisture easily. It's especially important to d...Read morerain your tank after each use—particularly if you tend to leave air in the tank for extended periods. Regular draining helps extend the life of your compressor and maintain its performance. Be sure to open the valve regularly to prevent water buildup and potential tank corrosion.

This is an authentic replacement part manufactured for use with Campbell Hausfeld air compressors. The extension is used when the oil needs to be drained further from the pump body. Oil must be removed from the pump prior to installing this extension. The oil drain extension is sold as an individual replacement part, please not the oil drain extension cap is sold separately.

This is a genuine OEM approved replacement drive belt. It is supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the belt that connects the pump and the electric motor. Over time these rubber belts tend to wear out and stretch eventually requiring replacement to maintain peak performance. Al...Read moreways make sure to clean the pulleys before installing the new belt, this will help to ensure longevity of the new belt. Includes one (1) belt per order. Replacing this belt is a very simple task that should only require a screwdriver. • Make sure to unplug the compressor and drain the tank • Remove the cover screws • Separate the cover from the unit • Remove the old belt • Clean the pulleys • Install the new belt • Secure the cover with the screws

This is a genuine OEM authorized replacement part which is specially designed for use with Ridgid air compressors. Check valve lets pressurized air flow into the tank and prevents it from flowing back into the pump. When replacing this part make sure to unplug the air compressor and release the air from the tank. Keep in mind this high-qu...Read moreality check valve is made of durable metal and is sold individually. Note that you would need a wrench to replace this part.

This is an authentic OEM component from Campbell Hausfeld. The oil drain cap is constructed of metal, and is fitted onto the oil drain extension. This cap is sold individually, and an adjustable wrench is helpful with the repair.

This is a genuine Campbell Hausfeld replacement part. The OEM pulley is manufactured for use with air compressors. This pulley connects to the motor's drive shaft and provides a surface that drives belt that links the pump assembly. The pulley can be purchased as an individual replacement part.