VT636000 Campbell Hausfeld Compressor - Overview

This replacement dipstick breather is designed for use with Campbell Hausfeld air compressors. It is secured in the opening on the crankcase allowing user to check and add the oil. A crankcase breather is a one way passage for gases to escape in a controlled manner from the crankcase of an internal combustion engine. It is made out of plastic and it is sold individually.

This is a genuine Campbell Hausfeld replacement part that has been sourced from the original manufacturer to be used with air compressors. The flywheel attaches to the pump's crankshaft and is used to rotate with the belt that is linked to the motor's pulley. This item is priced as a single replacement part.

This OEM part is sourced directly from the manufacturer and is an exact replacement for various air compressors. This Assembly includes the valve plate and two cardboard composite gaskets. It is gray in color, and its primary purpose is to provide a seal between the cylinder head and crankcase. This part will need to be replaced if you h...Read moreear air leaking, the tank takes a long time to fill, if it is worn or damaged, or if you removed the cylinder head from the crankcase for other repairs as gaskets are a one-time use part. You will need a screwdriver, a socket set, a wrench set, and a torque wrench to complete this repair. Customers rate this repair as Easy.

Includes the Head and Crankcase Gasket, O-rings and Seals

This replacement filter element is an authentic OEM item that is commonly utilized on Campbell Hausfeld air compressors. Its purpose is to filter out dust and debris from contaminating the engine with the air that goes into the carburetor. Please note this felt filter element is sold individually. Replacing it is a very simple task that does not require any tools.

This is a genuine OEM supplied replacement part that is specially designed for Campbell Hausfeld and Bostitch air compressors. It is the part that the piston attaches to. The piston is a central component of a two-cycle engine. It provides both the compression within the engine and it transfers the energy from combustion to the crankshaft...Read more which creates rotation. One durable metal connecting rod is included. Please note the piston is sold separately.

It is an identical replacement for a missing or a faulty cylinder head that was installed on a new unit. Please make sure to check appropriate diagrams for the correct location and use of this hardware. This authentic component is supplied directly from the original equipment manufacturer for Campbell Hausfeld air compressors. One durable...Read more metal cylinder head and the fasteners to secure it are included. A wrench set will be needed to perform this repair.

This genuine OEM replacement nipple is designed for use in air compressors, serving as a critical connector between the pressure switch, the tank, and the regulator. A damaged or corroded nipple can lead to air leaks and inconsistent pressure, affecting overall performance. To check for leaks, apply soapy water to the fittings around the ...Read morepressure switch and watch for bubbles. If replacement is necessary, the process typically involves disassembling the pressure switch. Begin by draining the tank using the valve at the bottom, then remove the coupler from the regulator and unthread the nipple. Access the wire connections by removing the pressure switch shroud, and carefully note the position of each wire before disconnecting them—starting with the motor wire, followed by the cord wires and ground wires. Remove the strain relief, pressure gauge, and the airline connecting the check valve to the switch. Finally, unthread the pressure switch from the tank nipple and remove the nipple itself. When reassembling, it is recommended to use thread tape to ensure a proper seal. This replacement part is sold individually.

Svc Compressor Pump Cw 75 X 51Mm

This is a genuine OEM part. The compression connector assembly is made by Campbell Hausfeld, and is compatible with many air compressor devices. The metal component secures the manifold to the compressor tank. This item is sold individually. A screwdriver and a pair of pliers are often helpful in making the replacement.

This is an authentic Campbell Hausfeld replacement part that has been sourced from the original manufacturer to be used with air compressors. The metal cap assembly is used to support the crankshaft bearing to keep the shaft in position on the wall of the crankcase. This item is available as an individual replacement part.