VT635600 (2006) Campbell Hausfeld Compressor - Overview

Designed for use in compressors, this genuine replacement part is used to provide a seal and prevent leaks. It is red, made of rubber, is not part of a kit or assembly, and is sold individually. When this part is worn, you will notice leaks from your machine, and it will need to be replaced. As with most rubber seals, this part is known...Read more to wear with regular use of your compressor, and will no longer be able to properly seal when it needs to be replaced. It is found at the bottom of the air tank, and you will need a wrench to complete this repair. Customers rate this repair as Easy.

This replacement regulator/manifold manifold assembly is specially manufactured for Campbell Hausfeld air compressors. The manifold kit consists of the manifold, the regulator, two pressure gauges, two quick-disconnects, and the nipple that connects the entire assembly to the air tank. The manifold kit will solve any problems related to a...Read more cracked manifold assembly, as well as any problems with the regulator. To complete this repair job correctly you may need : Phillip's screwdriver, hex drivers, long-nosed pliers, wrenches and heavy-duty wire cutters. • Depressurize the tank • Remove the manifold cover • Remove the pressure hose • Remove the pump assembly from the tank • Remove the manifold • Remove the manifold nipple • Transfer the safety valve • Install the new manifold kit • Secure the the pump assembly • Reinstall the hose • Reattach the manifold cover • Ensure everything is connected and test the compressor

This is a genuine Campbell Hausfeld replacement part that has been sourced from the original manufacturer to be used with air compressors. The flywheel attaches to the pump's crankshaft and is used to rotate with the belt that is linked to the motor's pulley. This item is priced as a single replacement part.

This OEM Check Valve is an exact replacement for certain air compressors. The purpose of this part is to allow pressurized air into the tank and stop it from flowing back into the pump. It is made of metal, is gold, is not part of a kit or assembly, and is sold individually. When the check valve is defective, the compressor will funcyio...Read moren normally until the tank fills with air. At that point, the pump will try to restart, but the engine will only produce a humming noise. Similarly, if the tank is full of air, the motor will make a humming noise without engaging. This part is located on the tank to the discharge tube and will need to be replaced if broken or worn. You will need a wrench set and a socket set to complete this repair. Customers rate this repair as Easy.

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

This genuine replacement pressure switch is specially designed for Campbell Hausfeld air compressors. It is sourced directly from the original equipment manufacturer and it is sold individually. The purpose of a pressure switch is to control when the compressor should start and stop building up pressure. The default setting of this pressu...Read morere switch is 100psi on and 135psi off. Please note this high-quality item is sold individually.

This is a genuine Campbell Hausfeld replacement drain valve, sold individually. When using an air compressor, moisture naturally condenses inside the tank. If this water is left sitting for too long, it can lead to internal rust and damage. The drain valve allows you to release this built-up moisture easily. It's especially important to d...Read morerain your tank after each use—particularly if you tend to leave air in the tank for extended periods. Regular draining helps extend the life of your compressor and maintain its performance. Be sure to open the valve regularly to prevent water buildup and potential tank corrosion.

1/4

It is an authentic replacement item that is specially supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the push-in fitting for the check valve which is sold separately. It is a quick-connect style fitting that is designed to accommodate for 1/4

This is a genuine OEM replacement part used with many air compressors machines. the exhaust tube is constructed of metal, and secures the tank to the cylinder head. This item helps with releasing the pressure overflow from the tank. An adjustable wrench is needed for the repair. This item is sold individually.

Svc Compressor Pump Cw 75 X 51Mm