VT634500 (2006) Campbell Hausfeld Compressor - Overview

Designed for use in compressors, this genuine replacement part is used to provide a seal and prevent leaks. It is red, made of rubber, is not part of a kit or assembly, and is sold individually. When this part is worn, you will notice leaks from your machine, and it will need to be replaced. As with most rubber seals, this part is known...Read more to wear with regular use of your compressor, and will no longer be able to properly seal when it needs to be replaced. It is found at the bottom of the air tank, and you will need a wrench to complete this repair. Customers rate this repair as Easy.

This replacement dipstick breather is designed for use with Campbell Hausfeld air compressors. It is secured in the opening on the crankcase allowing user to check and add the oil. A crankcase breather is a one way passage for gases to escape in a controlled manner from the crankcase of an internal combustion engine. It is made out of plastic and it is sold individually.

This is a genuine Campbell Hausfeld replacement part that has been sourced from the original manufacturer to be used with air compressors. The flywheel attaches to the pump's crankshaft and is used to rotate with the belt that is linked to the motor's pulley. This item is priced as a single replacement part.

This is an original manufacturer approved replacement air filter assembly which is specially designed for use with Campbell Hausfeld air compressors. Its purpose is to ensure the air that goes into the engine is free of dust and other harmful contaminants, over time it may get dirty and clogged eventually requiring replacement to maintain...Read more good air flow. This part consists of a durable metal housing with a pleated paper filter element.

This OEM Check Valve is an exact replacement for certain air compressors. The purpose of this part is to allow pressurized air into the tank and stop it from flowing back into the pump. It is made of metal, is gold, is not part of a kit or assembly, and is sold individually. When the check valve is defective, the compressor will funcyio...Read moren normally until the tank fills with air. At that point, the pump will try to restart, but the engine will only produce a humming noise. Similarly, if the tank is full of air, the motor will make a humming noise without engaging. This part is located on the tank to the discharge tube and will need to be replaced if broken or worn. You will need a wrench set and a socket set to complete this repair. Customers rate this repair as Easy.

This OEM part is sourced directly from the manufacturer and is an exact replacement for various air compressors. This Assembly includes the valve plate and two cardboard composite gaskets. It is gray in color, and its primary purpose is to provide a seal between the cylinder head and crankcase. This part will need to be replaced if you h...Read moreear air leaking, the tank takes a long time to fill, if it is worn or damaged, or if you removed the cylinder head from the crankcase for other repairs as gaskets are a one-time use part. You will need a screwdriver, a socket set, a wrench set, and a torque wrench to complete this repair. Customers rate this repair as Easy.

This Power Cord and Plug Assembly is an OEM sourced part for air compressors. It is wired to the electric motor in order to provide power from a standard outlet. This part is black, consists of a metal wire in a rubber insulated cable, and is sold individually. Depending on how worn it is, your compressor may no longer get power or may ...Read morehave sparks coming from it when it needs to be replaced. If you notice any visible damage such as exposed wires, cracks, or frays, it should be replaced. You will need a screwdriver, pliers, and a wrench to complete this repair. Customers rate this repair as Easy.

Includes the Head and Crankcase Gasket, O-rings and Seals

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

It is a genuine manufacturer-supplied item that is made for Campbell Hausfeld air compressors. O-rings are commonly utilized to provide an air-tight seal between connected components. Unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement. Check the diagrams for your model to ensur...Read moree the correct repair procedure. A screwdriver and a wrench set might be needed to replace this inspection port o-ring.

This heavy-duty pressure switch helps regulate when an air compressor starts and stops by controlling pressure between roughly 100 PSI and 135 PSI. Built with a four-port design and a convenient unloader valve, it replaces a worn or faulty switch that may cause the compressor to run inconsistently, leak air, or fail to shut off properly. ...Read moreDesigned for select compressor models, it offers a reliable, easy-to-install solution for restoring safe, consistent pressure control.