VT629800 Campbell Hausfeld Compressor - Overview

This is a genuine manufacturer sourced replacement regulator. It is specially designed for Campbell Hausfeld air compressors. This part adjusts the pressure of the air coming from the tank to the desired level. Please note, this only includes the metal regulator and the plastic knob. The valves, gauges and the pressure switch are all sold...Read more separately. To complete this repair you would need an a screwdriver, pliers and a set of wrenches. • First make sure to unplug the compressor • Drain the air from the tank • Disconnect all the valves and gauges from the regulator • Remove the old regulator • Secure the new regulator assembly • Reassemble and test the new regulator

This Power Cord and Plug Assembly is an OEM sourced part for air compressors. It is wired to the electric motor in order to provide power from a standard outlet. This part is black, consists of a metal wire in a rubber insulated cable, and is sold individually. Depending on how worn it is, your compressor may no longer get power or may ...Read morehave sparks coming from it when it needs to be replaced. If you notice any visible damage such as exposed wires, cracks, or frays, it should be replaced. You will need a screwdriver, pliers, and a wrench to complete this repair. Customers rate this repair as Easy.

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

This ASME safety valve is constructed of high-qualty metal, and is made for use with many air compressor models. Fastened to the manifold, the safety valve diminishes air pressure when the pump is not shut off at the proper setting. This important component is sold individually. A screwdriver, adjustable wrench and a pair of pliers are of...Read moreten necessary for the removal and replacement. Please refer to the specific manual for additional repair information.

This part is an OEM from Campbell Hausfeld. The axle bolt is compatible with many air compressors, and is sold individually. The metal bolt fastens the wheel to the base of the tank, providing movement to the device. A wrench and pliers are needed for the removal and replacement.

This is a genuine Campbell Hausfeld replacement drain valve, sold individually. When using an air compressor, moisture naturally condenses inside the tank. If this water is left sitting for too long, it can lead to internal rust and damage. The drain valve allows you to release this built-up moisture easily. It's especially important to d...Read morerain your tank after each use—particularly if you tend to leave air in the tank for extended periods. Regular draining helps extend the life of your compressor and maintain its performance. Be sure to open the valve regularly to prevent water buildup and potential tank corrosion.

This genuine OEM replacement nipple is designed for use in air compressors, serving as a critical connector between the pressure switch, the tank, and the regulator. A damaged or corroded nipple can lead to air leaks and inconsistent pressure, affecting overall performance. To check for leaks, apply soapy water to the fittings around the ...Read morepressure switch and watch for bubbles. If replacement is necessary, the process typically involves disassembling the pressure switch. Begin by draining the tank using the valve at the bottom, then remove the coupler from the regulator and unthread the nipple. Access the wire connections by removing the pressure switch shroud, and carefully note the position of each wire before disconnecting them—starting with the motor wire, followed by the cord wires and ground wires. Remove the strain relief, pressure gauge, and the airline connecting the check valve to the switch. Finally, unthread the pressure switch from the tank nipple and remove the nipple itself. When reassembling, it is recommended to use thread tape to ensure a proper seal. This replacement part is sold individually.

It is an authentic replacement item that is specially supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the push-in fitting for the check valve which is sold separately. It is a quick-connect style fitting that is designed to accommodate for 1/4

This is an authentic replacement part manufactured for use with Campbell Hausfeld air compressors. The extension is used when the oil needs to be drained further from the pump body. Oil must be removed from the pump prior to installing this extension. The oil drain extension is sold as an individual replacement part, please not the oil drain extension cap is sold separately.

This is a genuine OEM approved replacement drive belt. It is supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the belt that connects the pump and the electric motor. Over time these rubber belts tend to wear out and stretch eventually requiring replacement to maintain peak performance. Al...Read moreways make sure to clean the pulleys before installing the new belt, this will help to ensure longevity of the new belt. Includes one (1) belt per order. Replacing this belt is a very simple task that should only require a screwdriver. • Make sure to unplug the compressor and drain the tank • Remove the cover screws • Separate the cover from the unit • Remove the old belt • Clean the pulleys • Install the new belt • Secure the cover with the screws

This is a genuine OEM part. The compression connector assembly is made by Campbell Hausfeld, and is compatible with many air compressor devices. The metal component secures the manifold to the compressor tank. This item is sold individually. A screwdriver and a pair of pliers are often helpful in making the replacement.