VT629102 (2010) Campbell Hausfeld Compressor - Overview

Designed for use in compressors, this genuine replacement part is used to provide a seal and prevent leaks. It is red, made of rubber, is not part of a kit or assembly, and is sold individually. When this part is worn, you will notice leaks from your machine, and it will need to be replaced. As with most rubber seals, this part is known...Read more to wear with regular use of your compressor, and will no longer be able to properly seal when it needs to be replaced. It is found at the bottom of the air tank, and you will need a wrench to complete this repair. Customers rate this repair as Easy.

This OEM Check Valve is an exact replacement for certain air compressors. The purpose of this part is to allow pressurized air into the tank and stop it from flowing back into the pump. It is made of metal, is gold, is not part of a kit or assembly, and is sold individually. When the check valve is defective, the compressor will funcyio...Read moren normally until the tank fills with air. At that point, the pump will try to restart, but the engine will only produce a humming noise. Similarly, if the tank is full of air, the motor will make a humming noise without engaging. This part is located on the tank to the discharge tube and will need to be replaced if broken or worn. You will need a wrench set and a socket set to complete this repair. Customers rate this repair as Easy.

This is a genuine manufacturer sourced replacement regulator. It is specially designed for Campbell Hausfeld air compressors. This part adjusts the pressure of the air coming from the tank to the desired level. Please note, this only includes the metal regulator and the plastic knob. The valves, gauges and the pressure switch are all sold...Read more separately. To complete this repair you would need an a screwdriver, pliers and a set of wrenches. • First make sure to unplug the compressor • Drain the air from the tank • Disconnect all the valves and gauges from the regulator • Remove the old regulator • Secure the new regulator assembly • Reassemble and test the new regulator

This Power Cord and Plug Assembly is an OEM sourced part for air compressors. It is wired to the electric motor in order to provide power from a standard outlet. This part is black, consists of a metal wire in a rubber insulated cable, and is sold individually. Depending on how worn it is, your compressor may no longer get power or may ...Read morehave sparks coming from it when it needs to be replaced. If you notice any visible damage such as exposed wires, cracks, or frays, it should be replaced. You will need a screwdriver, pliers, and a wrench to complete this repair. Customers rate this repair as Easy.

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

It is a genuine manufacturer-supplied item that is made for Campbell Hausfeld air compressors. O-rings are commonly utilized to provide an air-tight seal between connected components. Unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement. Check the diagrams for your model to ensur...Read moree the correct repair procedure. A screwdriver and a wrench set might be needed to replace this inspection port o-ring.

This heavy-duty pressure switch helps regulate when an air compressor starts and stops by controlling pressure between roughly 100 PSI and 135 PSI. Built with a four-port design and a convenient unloader valve, it replaces a worn or faulty switch that may cause the compressor to run inconsistently, leak air, or fail to shut off properly. ...Read moreDesigned for select compressor models, it offers a reliable, easy-to-install solution for restoring safe, consistent pressure control.

It is a genuine OEM part that is made for Campbell Hausfeld air compressors. The unloader valve is an important component which allows a user to safely drain the air from the tank. Unfortunately, over time it may wear out or get damaged eventually requiring a replacement to ensure your unit operates properly. Note, this high-quality unloa...Read moreder includes multiple parts however it is sold as an individual component. Check the owner\\\'s manual and the diagrams of your model to ensure the correct installation and application. You will need a wrench set and pliers to perform this repair.

This is a genuine Campbell Hausfeld replacement drain valve, sold individually. When using an air compressor, moisture naturally condenses inside the tank. If this water is left sitting for too long, it can lead to internal rust and damage. The drain valve allows you to release this built-up moisture easily. It's especially important to d...Read morerain your tank after each use—particularly if you tend to leave air in the tank for extended periods. Regular draining helps extend the life of your compressor and maintain its performance. Be sure to open the valve regularly to prevent water buildup and potential tank corrosion.

It is an authentic replacement item that is specially supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the push-in fitting for the check valve which is sold separately. It is a quick-connect style fitting that is designed to accommodate for 1/4

This is a genuine OEM approved replacement drive belt. It is supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the belt that connects the pump and the electric motor. Over time these rubber belts tend to wear out and stretch eventually requiring replacement to maintain peak performance. Al...Read moreways make sure to clean the pulleys before installing the new belt, this will help to ensure longevity of the new belt. Includes one (1) belt per order. Replacing this belt is a very simple task that should only require a screwdriver. • Make sure to unplug the compressor and drain the tank • Remove the cover screws • Separate the cover from the unit • Remove the old belt • Clean the pulleys • Install the new belt • Secure the cover with the screws