This remote control is a device for adjusting your air conditioner settings. It requires two AAA batteries for operation. A malfunctioning remote control may have unresponsive buttons or signs of physical damage. You may also notice that your air conditioner does not consistently or promptly respond to commands from the remote control. Yo...Read moreu will then need to operate your unit manually, which can be inconvenient and limit access to certain features. Please note that this OEM replacement part is sold individually, and batteries are not included.
This part is a thermistor assembly and it works in conjunction with your room air conditioner. The thermistor is a sensor that attaches to the control board of your air conditioner. Once attached it will help regulate and monitor the temperature within the room. This model measures to be slightly under 20 inches in length, and it is black...Read more in color. The most common reason for needing to replace this part is if your appliance is no longer cooling properly. To replace this assembly, you will need a screwdriver set.
This fan assembly or also known as a condenser fan blade is used in air conditioners. The blade fits onto the motor shaft and distributes air over the condenser to cool the refrigerant before it goes into the evaporator. This part blows air parallel to the motor shaft which the blade rotates on to successfully circulate the air. It is mad...Read moree from white plastic. *Please note: This part is sold individually. This part comes with a slinger ring. Refer to the manual provided by the manufacturer for installation instructions and further guidance.
This control board, also known as a display board, is used for air conditioners. The control board regulates and carries the power to the various air conditioner components. If your control is defective or broken, it should be replaced or it will affect how your air conditioner functions. Check for other commonly defective parts that occu...Read morer before replacing the control board. Refer to the manual provided by the manufacturer for installation instructions and accurate guidance. Remember to unplug your appliance from the power source for safety before beginning this repair.
The installation kit contains the hardware you need to install the room air conditioner in a window. The kit also includes the accordion filler panels, installation brackets and seal.
This spring clamp is designed for your room air conditioner. This clamp holds the fan blade on the motor shaft so it can rotate during operation. If your fan blade is wobbling on the motor shaft, you may need to replace it. The part is made of metal and is approximately 3/4-inch in diameter. This is an OEM part sourced directly from the m...Read moreanufacturer. This spring clamp is sold individually. Before you begin this repair, make sure your air conditioner is disconnected from the power source. To complete this repair, you will likely need to remove the air conditioning unit from the wall.
If your air conditioner is not blowing cold air, the problem may be in the capacitor. If the capacitor fails, the compressor will not start and the fan will only blow warm air. The compressor and capacitor are located inside the cabinet and to gain access you will need to remove the cover. If the capacitor does not show any visible signs ...Read moreof damage you may require a qualified technician to test it. Make sure that the replacement capacitor has the same specifications as the original.
NOTE: Because capacitors carry a charge even when the unit is disconnected from the power, use extra caution when performing this repair.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bad thermistor
1 personfound this instruction helpful.
Cindy from Baltimore, MD
Really Easy
15 - 30 mins
Screw drivers
Took front cover off air conditioner and pulled it a little forward out of the outdoor housing. I then flipped the LED display section out to the left and exposed the patch panel. The next step was to remove the panel with a small screwdriver and disconnect the old thermistor plug. I then plugged in the new one, remove the old one from th
... Read moree grid bracket and placed the new one in. I then replaced everything else in reverse order. I have two LG air conditioners and they both have the same connection setup.
Read less
Was this helpful?
Thank you for voting!
Capacitor went out
2 of 6 peoplefound this instruction helpful.
Al from CROSS PLAINS, TX
Really Easy
30 - 60 mins
Pliers, Screw drivers
Unplugged and replugged everything and it worked very easy job thank you
Was this helpful?
Thank you for voting!
Bad thermister, unit would run constantly without cycling.
0 of 2 peoplefound this instruction helpful.
Gary from Aurora, CO
Really Easy
Less than 15 mins
Screw drivers
Remove the front cover. Slide the unit forward a few inches from the case. Remove 1 screw from the top on the control box. Unsnap the old thermister leads going into the circuit board. Snap in the new thermister and place the end in the plastic holder in front of the coils. Install front cover.