UT80953E Homelite Pressure Washer - Overview

This detergent suction kit, also known as a soap or chemical injection kit, is designed for use with a pressure washer. This is a genuine OEM part designed to inject soap into the water stream of your pressure washer, and includes the main injector valve, two differently sized O-rings, a spring, and a ball bearing. One end of this kit wil...Read morel be threaded into the washer, and the other will lead to your cleaner with a siphon, which is sold separately. This injection kit would need to be replaced if the nozzle is leaking, the injector fails to work properly, or water is getting into the soap dispenser. To replace, simply unscrew the previous injector and remove it, then fit the small O-ring inside the threaded end of the new injector, along with the ball bearing and then spring. Wrap the larger O-ring around the base of the threaded end, and apply a layer of lubricant, before installing the new injector and securing it.

This thermal release valve is for pressure washers. Thermal release valve attaches to the pump and releases the water and high pressure inside the pump if the water temperature exceeds normal operating temperatures. Wear work gloves to protect your hands when installing this part.

This OEM outlet tube, also known as a hose connector, allows pressurized water to flow from the pump of your pressure washer to the nozzle. Connecting the hose to the handle assembly and the spray wand, it is where the water exits from your machine so you can direct the stream towards a desired surface. You can tell if an outlet tube is b...Read moreroken when it has visible cracks or holes and when water leaks or sprays from the connection points or along the tube. A damaged or blocked tube can result in a loss of pressure and potentially premature wear or machine failure. To remove the outlet tube, use a wrench set to unscrew it from the pump. Please note that this replacement part is sold separately from the pump assembly.

(25 ft., 3000 psi) This water hose is for pressure washers. Water hose carries water from the pump to the spray wand. Wear work gloves to protect your hands when installing this part.

This is an original replacement part designed for the Homelite and Ryobi pressure washers listed below. This is a low pressure nozzle which draws soap/chemical mixture from the detergent tank, and gently spray a light coat onto a surface for cleaning. This soap nozzle may also be called a chemical injector tip. One (1) nozzle is included.

The collar attaches to the spindle. This item is made out of plastic and metal and is sold individually. This is an authentic part from Ryobi and Homelite for use in pressure washers. An allen wrench might be necessary during the installation of this part. It will require replacing if it becomes broken.

This is a genuine OEM supplied replacement part that is specially designed for Homelite and Ryobi generators and pressure washers. The ignition coil also is known as armature-magneto provides current for the ignition system by producing pulses of high voltage electricity for the spark plugs. While there are various reasons for ignition mo...Read moredule failure, the primary symptoms usually manifest in the form of extreme difficulty starting your equipment, and eventually, a no-start condition. It is made of high-quality metal with rubber insulated cord and it is sold individually.

It is a genuine OEM item that is made for use with Homelite and Ryobi and Homelite pressure washers. This is a special component which helps to provide a tight fit between connected components. Over time it may wear out or get damaged eventually requiring a replacement. Make sure to check the appropriate diagrams for your model to ensure ...Read morethe proper repair procedure. It is made of durable metal and is sold individually. A wrench might be needed to replace this inlet filter connector.

It is a genuine replacement part that is supplied by original equipment manufacturer for use with Homelite, Ridgid and Ryobi pressure washers. This siphon tube is used to deliver the chemical solution from the tank to the pump. Over time the tube may develop cracks allowing for leaks, if this happens this part can easily be replaced. It is made of durable flexible rubber material and it is sold individually.

The spark plug attaches to the cylinder head. This item is an OEM from Homelite and Ryobi for use in generators and pressure washers. This is available as an individual replacement part. A wrench might be needed during the installation process. It is made of metal and will require replacing if it breaks.