UT80735 Homelite Pressure Washer - Overview

This detergent suction kit, also known as a soap or chemical injection kit, is designed for use with a pressure washer. This is a genuine OEM part designed to inject soap into the water stream of your pressure washer, and includes the main injector valve, two differently sized O-rings, a spring, and a ball bearing. One end of this kit wil...Read morel be threaded into the washer, and the other will lead to your cleaner with a siphon, which is sold separately. This injection kit would need to be replaced if the nozzle is leaking, the injector fails to work properly, or water is getting into the soap dispenser. To replace, simply unscrew the previous injector and remove it, then fit the small O-ring inside the threaded end of the new injector, along with the ball bearing and then spring. Wrap the larger O-ring around the base of the threaded end, and apply a layer of lubricant, before installing the new injector and securing it.

This OEM outlet tube, also known as a hose connector, allows pressurized water to flow from the pump of your pressure washer to the nozzle. Connecting the hose to the handle assembly and the spray wand, it is where the water exits from your machine so you can direct the stream towards a desired surface. You can tell if an outlet tube is b...Read moreroken when it has visible cracks or holes and when water leaks or sprays from the connection points or along the tube. A damaged or blocked tube can result in a loss of pressure and potentially premature wear or machine failure. To remove the outlet tube, use a wrench set to unscrew it from the pump. Please note that this replacement part is sold separately from the pump assembly.

This is an authentic OEM part for pressure washers made by Homelite, Ryobi, and Husky. The inlet tube fits onto the pump and is made out of metal. When replacing this part a socket set may be needed. It is available as an individual replacement part, but also includes the metal bolt and the rubber o-ring.

It is a genuine item that is supplied by the original manufacturer for use with Homelite pressure washers. A washer is generally utilized to provide a tight fit between connected components. It provides an identical replacement for a damaged or a missing hardware that was installed on a new unit. Check the diagrams of your model for the e...Read morexact location and the correct application of this part. One durable metal washer is included. You may need a screwdriver or a wrench set to replace this washer.

This is an original part from Homelite. The lock nut (m8 x 1-1/4 mm) is compatible with many pressure washers, and is sold individually. The metal lock nut helps to secure various components of the pressure washer. A wrench, hex key and screwdriver are often needed for the installation.

It is a genuine replacement part that is supplied by original equipment manufacturer for use with Homelite, Ridgid and Ryobi pressure washers. This siphon tube is used to deliver the chemical solution from the tank to the pump. Over time the tube may develop cracks allowing for leaks, if this happens this part can easily be replaced. It is made of durable flexible rubber material and it is sold individually.

This is a genuine OEM sourced replacement part designed for use with Pressure Washers. This high pressure hose is made out of rubber/plastic material. It is 25 ft long and it is sold individually. This hose can be used on pumps that produce up to 3100 PSI. Easily connects to the washers with M22 connection. (25 Feet)

This is an authentic Homelite replacement part. The screw is designed by the manufacturer for use in pressure washers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of order...Read moreing the correct part. You will require a screwdriver when replacing this part. This item is sold individually.

This replacement washer is supplied directly from the original equipment manufacturer for use with Homelite pressure washers. It helps to distribute the pressure evenly between connected parts, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. This part is made of high-quality metal and it is sold individually.