UT33600 (090330013) Homelite Trimmer - Overview

This is an OEM Manufacturer Sourced replacement part used on certain Gas Powered String Trimmers. This part is made out of Foam and it is Sold Individually. Its purpose is to filter out dust and debris from contaminating the carburetor and engine. When replacing the filter you can open the package in comes in and put a bit of two cycle oi...Read morel in the bag and let it absorb into the filter. Then remove it from the bag and squeeze it with a paper towel to remove the excess oil. This will aid the filter in filtering out the unwanted debris.

This authentic OEM starter rope measures 42-inches and is for use with various models of outdoor power equipment. Made of nylon, this rope wraps around the starter recoil spring and when pulled, is used to start the engine. This rope is sold as an individual part, so any necessary grips are sold separately.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

It is an authentic OEM sourced replacement part designed for use with Homelite and Ryobi string trimmers and backpack blowers. This ignition module also known as an armature-magneto produces pulses of high voltage for the spark plugs. It is made out of metal with rubberized wire and the spark plug boot. To complete this repair you will n...Read moreeed a screwdriver set. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Set the gap • Reassemble and test the unit

Introducing the practical and sturdy Lower Housing Stringhead by Ryobi. This essential component lower housing has an arborless design and is an integral part for various Ryobi appliances offering firm support and secure placement. Renowned for its durability and excellent build quality this part helps extend your appliance's lifespan pro...Read moreviding smooth and efficient operation. Crafted using high-quality materials this lower housing stringhead promises a long-lasting performance ensuring your appliance remains reliable and efficient. So maximize the potential of your Ryobi appliance with this effective easy-to-install Ryobi Lower Housing Stringhead. Remember using Ryobi genuine parts maintains the original integrity of your equipment.

This is an authentic replacement part manufactured for use with trimmers. The special spring is used to provide compression for the spool to recede into the housing when bumping more string out of the trimmer head. This spring is sold as an individual replacement part, and will come with the complete trimmer head assembly. Please see model diagram for associative parts.

This OEM switch is used on a variety of different lawn equipment models and is sold individually. This switch is used to turn your lawn equipment on and off, so if your equipment is either not turning on, or this switch feels loose within its housing, it may be time to replace it. To remove it, separate the two halves of the housing which...Read more it connects to, disconnect the throttle and other wires with pliers, and depress the securing tabs. To install the new switch, click it into place within the housing and connect the appropriate wires to the two terminals, and then reconnect the throttle cable and other wires, and then simply align the two halves of the housing and secure with screws.

This carburetor gasket is an OEM replacement part for use in a variety of lawn and garden outdoor equipment. It seals the area between the carburetor and the intake manifold to prevent air and fuel from leaking. Over time, the gasket may wear down, crack, or warp due to normal aging, exposure to heat and chemicals, or improper installatio...Read moren. A faulty gasket will cause air and fuel to leak, resulting in hard starting, rough idling, fuel wastage, and overall lower engine performance. To replace the gasket, remove the air filter cover, air filter, and carburetor. Carefully pull off the old gasket, and thoroughly clean the sealing surface of all residues. Place the new carburetor gasket onto the intake manifold, and firmly press it in place. Reassemble the equipment parts in reverse order to complete your repair.

This Gear gear head assembly is designed to transfer power from the drive shaft to the cutting head, allowing the string trimmer or brush cutter to operate smoothly and efficiently. Housed in a durable gearcase, it supports reliable rotation and helps maintain consistent cutting performance during use. Replacing a worn or damaged gear hea...Read mored can resolve issues such as loss of power to the cutting head, excessive noise, or erratic operation, restoring dependable performance. A properly functioning gear head also helps reduce strain on the drive system, contributing to longer service life and more efficient trimming results.

This bolt helps to secure air filter and carburetor assemblies to the short block. It is sourced from original equipment manufacturer for use with string trimmers. Usually this bolt would need replacement if it is lost or has stripped threads or head socket. To install or remove this bolt a hex key/allen wrench would be needed.

This is an OEM sourced replacement part used on gas trimmers. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond the point of when they need to be replaced. Keepin...Read moreg an eye on equipment performance will determine when the centrifugal clutch requires attention. Please note the clutch drum, spacer and washer are all sold separately. This clutch is made out of metal and it is sold individually. To replace this item you would need a screwdriver and pliers.