UT32600 Homelite Trimmer - Overview

This spool retainer is sourced from the equipment manufacturer for use in trimmers. It is a plastic knob, measuring 2 inches in diameter, with a threaded metal bolt in the center. The retainer has a right hand thread, and it is used to secure the spool within the trimmer head to prevent it from coming loose during operation. The retainer ...Read moreengages with the trimmer head to lock the spool in place, while it also advances the cutting line for greater cutting efficiency. If the threads on the retainer bolt wear out or the plastic body becomes damaged, the retainer will be unable to engage with the trimmer head, causing the line to tangle, the spool to come loose, and lowering the cutting performance of the trimmer. Remove the trimmer head cover and detach the retainer from the assembly. Position the new spool retainer in the assembly and thread it firmly into place.

This grass deflector acts like a shield so that grass clippings are directed away from you and the surrounding areas while you are operating your trimmer. It is often located near the bottom of your trimmer, close to the cutting head. This assembly also includes the line cutting blade, which maintains the proper length of the trimmer line...Read more. If the assembly is cracked, bent, or missing, grass clippings may fly in unintended directions. This can be dangerous if your trimmer throws debris towards you or others nearby, so it is important to replace the damaged deflector. To replace the assembly, you will need a screwdriver to remove the flat washer, wing nut and, the hex screw from the grass deflector. Please be aware that this OEM grass deflector is sold individually.

This cutting head is for line trimmers. The cutting head attaches to the driveshaft and houses the cutting line. Wear work gloves to protect your hands when installing this part.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine Ruixing replacement part, it is sold individually. By pressing the bulb, it will purge the carburetor of air. Fuel will be forced up from the fuel tank through the fuel line then into the carburetor. Then the excess fuel will be forced back into the fuel tank through the fuel return line. At some time the primer will l...Read moreose its elasticity or crack and need to be replaced. We have an article and video on How to Replace a Primer Bulb, in our Repair Center. That can be found on the front page of our site.

This carburetor assembly in your lawn equipment mixes air and fuel to create a combustible mixture for the engine. A broken carburetor assembly can cause engine issues like running too lean or too rich, sputtering, stalling, fuel leaks, or a strong fuel odor. It is crucial to replace a faulty carburetor assembly promptly to avoid safety h...Read moreazards from fuel leaks and prevent engine failure due to fuel flooding. Replacing the carburetor requires a socket set. To replace the carburetor, use a socket set to remove the screws on the air filter base and disconnect the fuel lines before lifting it out of your machine. This OEM-verified assembly is sold separately from its fasteners.

It is an authentic OEM sourced replacement part designed for use with Homelite and Ryobi string trimmers and backpack blowers. This ignition module also known as an armature-magneto produces pulses of high voltage for the spark plugs. It is made out of metal with rubberized wire and the spark plug boot. To complete this repair you will n...Read moreeed a screwdriver set. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Set the gap • Reassemble and test the unit

This genuine fuel tank and cap assembly is found in your trimmer. The fuel tank holds the gasoline needed for your machine, while the cap seals it to prevent leaks and evaporation. It also prevents dirt and debris from getting into the engine and causing costly damage to it in the long run. You can usually find this assembly at the rear o...Read morer top of your trimmer, near the engine or handle. If the cap does not seal the tank properly and fuel spills from the assembly, it may be broken. A faulty cap can let debris or moisture into the tank, leading to contamination and engine issues. If the tank is damaged and can not hold enough fuel, your machine will have reduced runtime and require frequent refueling. To replace a damaged assembly, you will need a wrench or screwdriver to remove any bolts, clips, or screws holding the assembly in place. Be prepared to catch any fuel spillage with a container. Slide off any retaining clips or use pliers to release any clamps along the fuel lines before slowly pulling the assembly off your machine. These replacement parts are sourced directly from the original equipment manufacturer. This fuel tank and cap assembly also includes the fuel lines and the filter.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

This carburetor gasket is an OEM replacement part for use in a variety of lawn and garden outdoor equipment. It seals the area between the carburetor and the intake manifold to prevent air and fuel from leaking. Over time, the gasket may wear down, crack, or warp due to normal aging, exposure to heat and chemicals, or improper installatio...Read moren. A faulty gasket will cause air and fuel to leak, resulting in hard starting, rough idling, fuel wastage, and overall lower engine performance. To replace the gasket, remove the air filter cover, air filter, and carburetor. Carefully pull off the old gasket, and thoroughly clean the sealing surface of all residues. Place the new carburetor gasket onto the intake manifold, and firmly press it in place. Reassemble the equipment parts in reverse order to complete your repair.

This Gear gear head assembly is designed to transfer power from the drive shaft to the cutting head, allowing the string trimmer or brush cutter to operate smoothly and efficiently. Housed in a durable gearcase, it supports reliable rotation and helps maintain consistent cutting performance during use. Replacing a worn or damaged gear hea...Read mored can resolve issues such as loss of power to the cutting head, excessive noise, or erratic operation, restoring dependable performance. A properly functioning gear head also helps reduce strain on the drive system, contributing to longer service life and more efficient trimming results.

This bolt helps to secure air filter and carburetor assemblies to the short block. It is sourced from original equipment manufacturer for use with string trimmers. Usually this bolt would need replacement if it is lost or has stripped threads or head socket. To install or remove this bolt a hex key/allen wrench would be needed.