UT10520 Homelite Chainsaw - Overview

This is a genuine OEM replacement part, it is made out of Metal with Fabric Filter Material. It is sold individually and is used on a variety of Lawn and Garden Equipment. This is an in-tank fuel filter which makes sure that the fuel delivered to the engine is free of any debris or contaminants. It will over time become clogged and restrict the fuel getting to the engine so it will need to be replaced.

This is an adjusting pin kit, also known as a chain tensioner kit, for various chainsaw models. This genuine OEM kit features an adjustment/tensioner pin and bar adjustment screw to modify and change the tension of the chain, so when the chain becomes loose over time, you can tighten or loosen it depending on your needs. If the chain for ...Read moreyour chainsaw becomes too loose, it can come off the bar and cause injury, but if too tight can damage the bar or engine of the chainsaw. This assembly is installed on or near the clutch assembly of the chainsaw and is usually accessible by removing an access panel. Replacing this assembly is easy and only requires a wrench and screwdriver. First, disengage the chain brake and remove the screws securing the side panel of your chainsaw. Remove the side panel and locate the bar adjustment screw. Loosen the old adjustment screw and remove it and the tensioner pin. Thread the new adjustment screw through the new tensioner pin until the screw is locked into place. Then rotate the screw counterclockwise until the pin is in the middle of the screw. Replace the cover panel assembly and test the chainsaw.

This is an authentic OEM sourced replacement screw designed for use with chainsaws. It helps to secure the muffler assembly. This part is made out of metal and it is sold individually. You would need a wrench to tighten/loosen this screw.

This is an OEM replacement part,it is sold individually. The purpose of the Air Purge Bulb is to purge all of the air from the carburetor. It then brings fuel up through the fuel line in the tank into the carburetor. Once the carburetor is full of fuel the Bulb will force the excess fuel back into the tank through the fuel return line. ...Read moreOver time the bulb will loose it elasticity or begin to crack, it will need to be replaced at this time.

This is a genuine OEM replacement part, it is sold individually. The purpose of this filter is to keep dirt and other small particles from entering the carburetor and engine and causing internal engine damage. Once this type of filter gets clogged or dirty it should be changed (Not Cleaned). This is to prevent restricted air flow and foreign matter from entering the engine.

This is a Manufacturer Sourced replacement part for Lawn and Garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This Locking Nut has multiple uses based on your tool. You would need a Wrench to tighten or loosen this Hex Nut.

Genuine OEM replacement part, this item is sold individually. The purpose of the 631036001 Guide Bar Plate is to assist in keeping the Chainsaw Blade inline. Also with out this plate, if the chain was to come of the chain bar, this part would help keep the housing of the Chainsaw from being damaged.

This steel OEM part is used in Homelite and Ryobi chainsaws. The sprockets connect to and control the saw chain. This is a commonly replaced part because of its high-wear function. Please note that washers and e-rings are sold separately.

Genuine OEM replacement part, this item is sold individually. This is part of the Guide bar adjustment kit. The chain bar is sandwiched between this part and part number 631036001 Guide Bar Plate. You can obtain the complete Guide Bar Adjust Kit, by ordering part number UP06966A.

It is an authentic OEM supplied hardware that is designed for use with Homelite and Ryobi chainsaws. This special screw is used to secure the Safe-T-Tip to the bar. Please note this high quality hex head screw with a washer is sold individually, you will need a wrench to secure or remove it.

Authentic manufacturer approved replacement bolt made for use with string trimmers and chainsaws. This is a standard hardware with multiple uses based on your tool. Please refer to specific diagrams for correct application. This bolt has a hex socket head which requires a hex key/allen wrench for installation. It is sold individually.