UT100550 Homelite Chainsaw - Overview

This is a rubber primer bulb with a plastic adapter attachment that is used on a variety of lawn and garden equipment models. This bulb attaches to the carburetor and is used to pump gasoline from the fuel tank into the gas chamber of the carburetor. Over time and through regular use, the primer bulb will lose its elasticity and may crack...Read more, requiring it to be replaced. To replace your primer bulb, you simply need to locate the bulb on your machine, unscrew the housing and remove the bulb, and secure the new one. This bulb is sold as an individual part and has a 2.25cm (7/8-inch) outer-diameter and a 3.33cm (1.3125-inch) height.

This is a genuine OEM replacement part, it is sold individually. The purpose of this filter is to keep dirt and other small particles from entering the carburetor and engine and causing internal engine damage. Once this type of filter gets clogged or dirty it should be changed (Not Cleaned). This is to prevent restricted air flow and foreign matter from entering the engine.

This is a Manufacturer Sourced replacement part for Lawn and Garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This Locking Nut has multiple uses based on your tool. You would need a Wrench to tighten or loosen this Hex Nut.

This steel OEM part is used in Homelite and Ryobi chainsaws. The sprockets connect to and control the saw chain. This is a commonly replaced part because of its high-wear function. Please note that washers and e-rings are sold separately.

Genuine OEM replacement part, this item is sold individually. This is part of the Guide bar adjustment kit. The chain bar is sandwiched between this part and part number 631036001 Guide Bar Plate. You can obtain the complete Guide Bar Adjust Kit, by ordering part number UP06966A.

It is an authentic OEM supplied hardware that is designed for use with Homelite and Ryobi chainsaws. This special screw is used to secure the Safe-T-Tip to the bar. Please note this high quality hex head screw with a washer is sold individually, you will need a wrench to secure or remove it.

Authentic manufacturer approved replacement bolt made for use with string trimmers and chainsaws. This is a standard hardware with multiple uses based on your tool. Please refer to specific diagrams for correct application. This bolt has a hex socket head which requires a hex key/allen wrench for installation. It is sold individually.

This is an authentic replacement screw which is supplied by the original equipment manufacturer for use with handheld lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. This high-quality Torx screw is made of durable metal and it is sold individually.

This replacement ignition coil also known as a magneto is a genuine OEM part. It is specially produced for Homelite and Ryobi chainsaws. It plays an important role, because it producing pulses of high voltage for the spark plugs. It is made out of metal with a rubber insulated wire and a spark plug boot. Please note replacing this module...Read more would differ based on your unit, however the basic steps would be the same. To complete this repair you will need screwdriver and a wrench set. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Set the gap • Reassemble and test the unit

This is a genuine replacement part manufactured for use with chainsaws. The throttle cable is the linkage between the throttle trigger and the carburetor. The small connectors at the end of the cable can break or wear out, and replacing a broken cable is an easy way to extend the life of the chainsaw. This throttle cable is sold as an individual replacement part.

This is a genuine OEM sourced part that is intended to be used with Homelite chainsaws and Ryobi pruners and chainsaws. The plastic oil cap is used to cover the oil tank fill spout to prevent spills and to stop contaminants from entering the tank. The cap includes the tether that connects the cap to the tank and the cap is priced as a single item.