UT09510 Homelite Leaf Blower / Vacuum - Overview

This authentic OEM starter rope measures 42-inches and is for use with various models of outdoor power equipment. Made of nylon, this rope wraps around the starter recoil spring and when pulled, is used to start the engine. This rope is sold as an individual part, so any necessary grips are sold separately.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine Ruixing replacement part, it is sold individually. By pressing the bulb, it will purge the carburetor of air. Fuel will be forced up from the fuel tank through the fuel line then into the carburetor. Then the excess fuel will be forced back into the fuel tank through the fuel return line. At some time the primer will l...Read moreose its elasticity or crack and need to be replaced. We have an article and video on How to Replace a Primer Bulb, in our Repair Center. That can be found on the front page of our site.

It is an authentic OEM sourced replacement part designed for use with Homelite and Ryobi string trimmers and backpack blowers. This ignition module also known as an armature-magneto produces pulses of high voltage for the spark plugs. It is made out of metal with rubberized wire and the spark plug boot. To complete this repair you will n...Read moreeed a screwdriver set. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Set the gap • Reassemble and test the unit

This carburetor is for line trimmers. Carburetor mixes air and gas before the fuel mix goes to the engine. Wear work gloves to protect your hands and work in a well-ventilated area during this repair.

This is an authentic OEM sourced replacement momentary contact switch. It is specially designed for Homelite and Ryobi blowers and vacuums. It is the part of the tool handling on and off function of the tool. Please note, these mechanical switches have will over time wear out requiring replacement. This switch has a plastic body and it is sold individually. To replace this item no tools would be needed.

This manufacturer approved replacement starter pulley is designed for use with gas blowers/vacuums. This recoil pulley is susceptible to a normal wear due to constant wear and will eventually require replacement. It is made out of plastic and it is sold individually. Please note, housing, rope and starter grip are all sold separately. To complete this repair you will need a screwdriver and an allen wrench/hex key.

Genuine OEM replacement part, this item is sold individually. This part is used on the carburetors on the outdoor power equipment listed below. Because this part is used quite frequently it has a tendency to wear. To replace it, simply press it on the Choke Shaft of the carburetor.

Genuine Manufacturer Sourced replacement part used on Blowers/Vacuums and String Trimmers. This part is made out of Composite Material and it is Sold Individually. This Gasket provides an Air Tight Seal between the Heat Dam and Carburetor which acts as a spacer allowing it to stay cool.

Genuine Manufacturer Sourced replacement part used on certain Hedge Trimmers and Blowers. This part is made out of Plastic and it is Sold Individually. Heat Dam acts as a spacer for carburetor allowing it to stay cool.

This fuel tank assembly is an OEM replacement part supplied by the manufacturer. It is commonly used in Ryobi and Homelite blower/vacuums. This fuel tank assembly contains the gasoline needed to operate these machines. This assembly should be replaced if any of the included parts are missing or damaged. A screwdriver is required to comple...Read morete this replacement. -Remove the three mounting screws -Disconnect the two fuel lines -Remove old tank and replace with the new -Connect the two fuel lines -Reattach the three mounting screws