UT08095 (I25MHV -) Homelite Leaf Blower / Vacuum - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine OEM replacement part, it is sold individually. The purpose of the 900994004 Carburetor Gasket is to prevent an air leak, which would cause the engine to run poorly. It is advised to replace these gaskets when replacing or repairing the carburetor.

This crankcase cover gasket seals the crankcase cover of your lawn equipment engine, preventing air or fuel leaks and maintaining proper internal pressure. It is sized at 2 1/2 inches by 2 1/2 inches and is commonly found where the crankcase cover attaches to the engine block. You can tell if a crankcase cover gasket is broken if there is...Read more oil around the edges of the cover. Your machine may also experience a loss of power or unusual noise. If the gasket is not replaced, your machine may have fuel leaks or decreased performance. Debris and contaminants will also enter the engine, reducing the lifespan of your machine. When replacing the gasket, use a wrench or socket to unthread any bolts securing the crankcase cover. You will then be able to take the gasket off your machine. Bear in mind that this OEM gasket is sold individually.

Genuine OEM replacement part, this item is sold individually. This Fuel Cap is is on the fuel tank on the outdoor products shown below. This is a vented Fuel Cap. It includes a gasket inside the Cap.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

This is a genuine OEM replacement part, it is sold individually. The purpose of this part is to connect the fuel line extending from the fuel tank to the fuel line that connects to the carburetor. Over time the fuel lines will become brittle and oversized. They will have to be replaced. This would be a good time to replace the Fuel Fitting also.

This is a genuine OEM sourced replacement starter rope, not an aftermarket equivalent. This part is used to pull start Homelite and Ryobi handheld lawn and garden equipment. This rope is made from durable fabric and it is sold individually. Please note, the grip handle is sold separately. Replacing this starter rope you will need a screwdriver.

This item has been OEM sourced to ensure a high-quality standard. The rotor is intended to be used with trimmers, blowers, and chainsaws from Homelite and Ryobi. The rotor is the engine's flywheel and is used as one of the main components in the ignition sequence. The rotor has magnets on its edge that create an electric charge as they pa...Read moress the ignition module, this ignites the air/fuel mixture in the cylinder which rotates the crankshaft and the drive shaft. This item includes the pawls that make contact with the recoil starter pulley when the starter rope is pulled.

This is an authentic replacement screw which is supplied by the original equipment manufacturer for use with handheld lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. This high-quality Torx screw is made of durable metal and it is sold individually.

A genuine replacement part which is supplied directly from the original equipment manufacturer for use with Homelite and Ryobi handheld lawn and garden equipment. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality screw is made of durable metal and is sold individually.

This metal OEM wire clamp is a type of fastener that holds hoses or cables together and keeps them from moving while your machine is operating. It is mostly found in lawn equipment to attach its fuel line to the filter. You can tell that the metal clamp is broken if the parts it was securing has become loose or has fallen off. When this h...Read moreappens, your equipment may start leaking and can pose as a safety hazard. To remove the wire clamp, you need a pair of pliers. Grip onto a broken clamp before twisting it counterclockwise to release it from your machine. This item is sold separately.