UT-74125-D Homelite Chainsaw - Overview

This spark plug is an authentic Craftsman replacement part, and is compatible with chainsaws. The spark plug produces a spark that ignites the fuel in the engine. A socket wrench will be needed to install or replace the spark plug. This part is made of ceramic with metal and is sold individually.

This is an adjusting pin kit, also known as a chain tensioner kit, for various chainsaw models. This genuine OEM kit features an adjustment/tensioner pin and bar adjustment screw to modify and change the tension of the chain, so when the chain becomes loose over time, you can tighten or loosen it depending on your needs. If the chain for ...Read moreyour chainsaw becomes too loose, it can come off the bar and cause injury, but if too tight can damage the bar or engine of the chainsaw. This assembly is installed on or near the clutch assembly of the chainsaw and is usually accessible by removing an access panel. Replacing this assembly is easy and only requires a wrench and screwdriver. First, disengage the chain brake and remove the screws securing the side panel of your chainsaw. Remove the side panel and locate the bar adjustment screw. Loosen the old adjustment screw and remove it and the tensioner pin. Thread the new adjustment screw through the new tensioner pin until the screw is locked into place. Then rotate the screw counterclockwise until the pin is in the middle of the screw. Replace the cover panel assembly and test the chainsaw.

This is a genuine OEM replacement part, it is sold individually. The purpose of this filter is to keep dirt and other small particles from entering the carburetor and engine and causing internal engine damage. Once this type of filter gets clogged or dirty it should be changed (Not Cleaned). This is to prevent restricted air flow and foreign matter from entering the engine.

Genuine OEM replacement part, this item is sold individually. The purpose of the 631036001 Guide Bar Plate is to assist in keeping the Chainsaw Blade inline. Also with out this plate, if the chain was to come of the chain bar, this part would help keep the housing of the Chainsaw from being damaged.

Ergo grip starter handle

Genuine OEM replacement part, this item is sold individually. This is part of the Guide bar adjustment kit. The chain bar is sandwiched between this part and part number 631036001 Guide Bar Plate. You can obtain the complete Guide Bar Adjust Kit, by ordering part number UP06966A.

This authentic part is supplied by the original equipment manufacturer for use with Ryobi and Homelite chainsaws. The spring is an important part of the starter mechanism. Unfortunately, over time it will wear out and it may begin to stretch eventually requiring a replacement. One durable metal spring with a container is included. Check t...Read morehe diagrams for your model to ensure the proper repair procedure. A screwdriver might be needed to replace this part.

This rope is part of the pull starter system on Homelite and Ryobi gas powered lawn and garden equipment. It is an authentic manufacturer sourced replacement part, not an aftermarket equivalent. When the rope is pulled to start the engine, it is returned back into the starter pulley by means of the starter spring which is sold separately....Read more Please note, this rope is made out of strong fabric and it is sold individually. Replacing this starter rope you will need a screwdriver. • Remove the housing-cover • Remove the carburetor • Disconnect the clutch housing • Bind the engine • Remove the clutch drum • Remove the clutch • Remove the starter • Remove the starter handle • Remove the recoil pulley • Remove the old rope • Install the new starter rope • Reassemble and test the unit

This is an authentic replacement screw which is supplied by the original equipment manufacturer for use with handheld lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. This high-quality Torx screw is made of durable metal and it is sold individually.

This is a genuine replacement part manufactured for use with chainsaws. The throttle cable is the linkage between the throttle trigger and the carburetor. The small connectors at the end of the cable can break or wear out, and replacing a broken cable is an easy way to extend the life of the chainsaw. This throttle cable is sold as an individual replacement part.

The hex nut attaches to the drive case cover. This part is made of metal and is sold individually even though many nuts may be needed during installation. This part may become stripped or lost and will need to be replaced. A wrench will be needed when replacing this part. It is an authentic OEM sourced item which is specially designed for use with Homelite and Ryobi chainsaws.