UT-50901 Homelite Edger - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side...Read more which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

This genuine fuel tank and cap assembly is found in your trimmer. The fuel tank holds the gasoline needed for your machine, while the cap seals it to prevent leaks and evaporation. It also prevents dirt and debris from getting into the engine and causing costly damage to it in the long run. You can usually find this assembly at the rear o...Read morer top of your trimmer, near the engine or handle. If the cap does not seal the tank properly and fuel spills from the assembly, it may be broken. A faulty cap can let debris or moisture into the tank, leading to contamination and engine issues. If the tank is damaged and can not hold enough fuel, your machine will have reduced runtime and require frequent refueling. To replace a damaged assembly, you will need a wrench or screwdriver to remove any bolts, clips, or screws holding the assembly in place. Be prepared to catch any fuel spillage with a container. Slide off any retaining clips or use pliers to release any clamps along the fuel lines before slowly pulling the assembly off your machine. These replacement parts are sourced directly from the original equipment manufacturer. This fuel tank and cap assembly also includes the fuel lines and the filter.

This carburetor gasket is an OEM replacement part for use in a variety of lawn and garden outdoor equipment. It seals the area between the carburetor and the intake manifold to prevent air and fuel from leaking. Over time, the gasket may wear down, crack, or warp due to normal aging, exposure to heat and chemicals, or improper installatio...Read moren. A faulty gasket will cause air and fuel to leak, resulting in hard starting, rough idling, fuel wastage, and overall lower engine performance. To replace the gasket, remove the air filter cover, air filter, and carburetor. Carefully pull off the old gasket, and thoroughly clean the sealing surface of all residues. Place the new carburetor gasket onto the intake manifold, and firmly press it in place. Reassemble the equipment parts in reverse order to complete your repair.

This is an OEM sourced replacement part used on gas trimmers. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond the point of when they need to be replaced. Keepin...Read moreg an eye on equipment performance will determine when the centrifugal clutch requires attention. Please note the clutch drum, spacer and washer are all sold separately. This clutch is made out of metal and it is sold individually. To replace this item you would need a screwdriver and pliers.

Genuine OEM replacement part, this item is sold individually. The purpose of the 901551001 Intake Gasket is to create a seal between the Heat Dam and the cylinder head. Over time because of the heat it is exposed to this gasket will deteriorate and will have to be replaced.

This hanger cap, also known as a mounting clip, is a genuine replacement part from the equipment manufacturer to help you store hand attachments that you are using. It is a small plastic cap that acts as a protective cover for the hanger hook in lawn and garden equipment. It protects the hook from damage and keeps it from getting caught o...Read moren other items. You will need one cap for each of the attachments or tools you have. The cap will need to be replaced if it is damaged or can no longer stay attached to the equipment. To install the new cap, simply place the new cap at the end of the attachment on your equipment. Sold individually.

This is a genuine OEM supplied replacement gearbox assembly that is specially designed for Ryobi and Homelite handheld lawn and garden equipment. It is attached to the lower boom assembly and it is what drives the trimmer head. Over time the internal components such as gears may wear out and begin to fail eventually requiring a replacement. It is made from durable metal and it is sold individually.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Homelite and Ryobi handheld lawn and garden equipment. This is the special screw which is utilized to secure the gear head, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. K...Read moreeep in mind this durable metal hex head screw is sold individually, you will need a wrench to secure or remove it.

This is a genuine OEM sourced replacement part designed for use with gas powered string trimmers and blowers. The ignition module also known as armature-magneto provides current for the ignition system by producing pulses of high voltage for the spark plugs. It is made out of metal with some plastic components and it is sold individually....Read more Includes a spark plug boot. To complete this repair you would need screwdriver set. Please note replacing this module would differ based on your unit, however the basic steps would be the same. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Install the red wire • Set the gap • Install the black wire • Reassembly and test the unit

This replacement part is sourced directly from original equipment manufacturer. This switch is designed for use with a variety of power equipment. It is an important piece of hardware responsible for handling on/off function of equipment. Because switches have internal mechanical part, over time they will break down requiring replacement....Read more This switch has a plastic body and it includes a clear plastic cover. To complete this repair you would need a screwdriver. • First make sure the unit is not plugged in • Then you want to separate housing pieces by removing screws • Disconnect wires from the old switch • Replace old switch with a new one • Reconnect wires • Reassemble and test the unit