UT-21546 Homelite Trimmer - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This carburetor gasket is an OEM replacement part for use in a variety of lawn and garden outdoor equipment. It seals the area between the carburetor and the intake manifold to prevent air and fuel from leaking. Over time, the gasket may wear down, crack, or warp due to normal aging, exposure to heat and chemicals, or improper installatio...Read moren. A faulty gasket will cause air and fuel to leak, resulting in hard starting, rough idling, fuel wastage, and overall lower engine performance. To replace the gasket, remove the air filter cover, air filter, and carburetor. Carefully pull off the old gasket, and thoroughly clean the sealing surface of all residues. Place the new carburetor gasket onto the intake manifold, and firmly press it in place. Reassemble the equipment parts in reverse order to complete your repair.

This is a genuine OEM replacement part, it is sold individually. The Housing and Eyelet contain the spring and the spool and string for the models listed below. The cutting string is inserted through the eyelets, then the spool is inserted into the housing, it is then attached by the spool retainer.

This is an authentic OEM sourced replacement starter housing assembly is designed for use with Homelite handheld trimmers. It is the mechanism that allows a user to pull-start the engine. It includes a plastic housing, a starter pulley, a starter spring and a pull rope with a grip. If any of the components on your assembly are damaged, th...Read moreis will provide an easy all in one replacement. Please note, the hardware to secure it is sold separately. You will need a screwdriver to perform this repair.

Genuine OEM replacement part, this item is sold individually. The purpose of the 901551001 Intake Gasket is to create a seal between the Heat Dam and the cylinder head. Over time because of the heat it is exposed to this gasket will deteriorate and will have to be replaced.

Genuine Homelite replacement part, this item is sold individually. Included with the fuel tank assembly, is the fuel line with filter, the return fuel line, and fuel cap. It is designed to hold the fuel for the outdoor products listed below. A Torx screwdriver is needed for replacement.

This is a genuine OEM sourced replacement starter rope, not an aftermarket equivalent. This part is used to pull start Homelite and Ryobi handheld lawn and garden equipment. This rope is made from durable fabric and it is sold individually. Please note, the grip handle is sold separately. Replacing this starter rope you will need a screwdriver.

This is a genuine OEM sourced replacement part designed for use with gas powered string trimmers and blowers. The ignition module also known as armature-magneto provides current for the ignition system by producing pulses of high voltage for the spark plugs. It is made out of metal with some plastic components and it is sold individually....Read more Includes a spark plug boot. To complete this repair you would need screwdriver set. Please note replacing this module would differ based on your unit, however the basic steps would be the same. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Install the red wire • Set the gap • Install the black wire • Reassembly and test the unit

This replacement part is sourced directly from original equipment manufacturer. This switch is designed for use with a variety of power equipment. It is an important piece of hardware responsible for handling on/off function of equipment. Because switches have internal mechanical part, over time they will break down requiring replacement....Read more This switch has a plastic body and it includes a clear plastic cover. To complete this repair you would need a screwdriver. • First make sure the unit is not plugged in • Then you want to separate housing pieces by removing screws • Disconnect wires from the old switch • Replace old switch with a new one • Reconnect wires • Reassemble and test the unit

Genuine OEM replacement part, This item is sold as a kit. This is the complete Stringhead Assembly for the Trimmers shown below. It is a dual line head. To install this part, slide it on the spindle or shaft of the Trimmer The kit contains two Spool Retainers to secure the Stringhead. The red one has left hand threads and the black one ha...Read mores right hand threads. It will depend on the model you have, on which Spool Retainer to use. The cutting line diameter used in this Stringhead is .095

Genuine Homelite replacement part, this item is sold individually. A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below th...Read moree Venturi is a butterfly valve called the throttle valve ' a rotating disc that can be turned end-on to the airflow, so as to hardly restrict the flow at all, or can be rotated so that it (almost) completely blocks the flow of air. This valve controls the flow of air through the carburetor throat and thus the quantity of air/fuel mixture the system will deliver, thereby regulating engine power and speed. The throttle is connected, usually through a cable or a mechanical linkage of rods and joints. Fuel is introduced into the air stream through small holes at the narrowest part of the Venturi and at other places where pressure will be lowered when not running on full throttle.