UT-20780 Homelite Trimmer - Overview

The Fuel Tank is an OEM replacement part. It is compatible with the models shown below. It includes the fuel lines, fuel cap and fuel filter. If you need to order the fuel tank bumpers, they are sold individually as part number 98792.

This grass deflector acts like a shield so that grass clippings are directed away from you and the surrounding areas while you are operating your trimmer. It is often located near the bottom of your trimmer, close to the cutting head. This assembly also includes the line cutting blade, which maintains the proper length of the trimmer line...Read more. If the assembly is cracked, bent, or missing, grass clippings may fly in unintended directions. This can be dangerous if your trimmer throws debris towards you or others nearby, so it is important to replace the damaged deflector. To replace the assembly, you will need a screwdriver to remove the flat washer, wing nut and, the hex screw from the grass deflector. Please be aware that this OEM grass deflector is sold individually.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

This is a genuine OEM replacement part, it is sold individually. The purpose of the 900994004 Carburetor Gasket is to prevent an air leak, which would cause the engine to run poorly. It is advised to replace these gaskets when replacing or repairing the carburetor.

Genuine OEM replacement part, this item is sold individually. This Fuel Cap is is on the fuel tank on the outdoor products shown below. This is a vented Fuel Cap. It includes a gasket inside the Cap.

The air filter in your trimmer keeps the engine running smoothly. It filters out dirt and debris from the air before it enters the engine, ensuring that clean air is used for efficient fuel combustion. This helps protect the engine and maintain its performance. If the air filter is clogged or damaged, it should be replaced to avoid reduce...Read mored engine performance, increased fuel consumption, and potential engine damage. To remove the existing filter, consult your user guide to locate the air filter housing. Depress the locking tab on the housing cover, lift it off, and remove the filter. Follow any specific installation instructions for your machine model. Please note that this OEM air filter is sold individually.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

This is a genuine OEM replacement part, it is sold individually. This is the fuel pick-up line it is connected to the line coming from the fuel tank by means of a inline fuel fitting. It is then connected to the carburetor. It is used on the model numbers shown below.

It is an authentic manufacturer-approved replacement trimmer head assembly that is specially designed for use with Homelite and Ryobi string trimmers. This trimmer head is designed to quickly and efficiently cut through the grass. It is a complete assembly which includes the bump head knob, spool with string, cover and metal eyelets. Please note this high-quality string head assembly is sold individually.

Genuine OEM replacement part, This item is sold as a kit. This is the complete Stringhead Assembly for the Trimmers shown below. It is a dual line head. To install this part, slide it on the spindle or shaft of the Trimmer The kit contains two Spool Retainers to secure the Stringhead. The red one has left hand threads and the black one ha...Read mores right hand threads. It will depend on the model you have, on which Spool Retainer to use. The cutting line diameter used in this Stringhead is .080

Throttle Cable with a 11" Conduit. For a 15" conduit see Related Item.