UT-08951 Homelite Leaf Blower / Vacuum - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This carburetor gasket is an OEM replacement part for use in a variety of lawn and garden outdoor equipment. It seals the area between the carburetor and the intake manifold to prevent air and fuel from leaking. Over time, the gasket may wear down, crack, or warp due to normal aging, exposure to heat and chemicals, or improper installatio...Read moren. A faulty gasket will cause air and fuel to leak, resulting in hard starting, rough idling, fuel wastage, and overall lower engine performance. To replace the gasket, remove the air filter cover, air filter, and carburetor. Carefully pull off the old gasket, and thoroughly clean the sealing surface of all residues. Place the new carburetor gasket onto the intake manifold, and firmly press it in place. Reassemble the equipment parts in reverse order to complete your repair.

Genuine OEM replacement part, this item is sold individually. The purpose of the 901551001 Intake Gasket is to create a seal between the Heat Dam and the cylinder head. Over time because of the heat it is exposed to this gasket will deteriorate and will have to be replaced.

This is a genuine OEM sourced replacement part designed for use with gas powered string trimmers and blowers. The ignition module also known as armature-magneto provides current for the ignition system by producing pulses of high voltage for the spark plugs. It is made out of metal with some plastic components and it is sold individually....Read more Includes a spark plug boot. To complete this repair you would need screwdriver set. Please note replacing this module would differ based on your unit, however the basic steps would be the same. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Install the red wire • Set the gap • Install the black wire • Reassembly and test the unit

This is an authentic OEM sourced replacement screw. It is specially manufactured for use with a variety of handheld lawn and garden equipment. This is a standard hardware which has multiple applications based on your unit. Please refer to appropriate diagrams for correct location and application of this screw. This screw is made out of me...Read moretal and it is sold individually. To remove or install it you will need a torx screwdriver.

This replacement screw is a high-quality hardware that is supplied by the original equipment manufacturer for use with Homelite and Ryobi handheld lawn and garden equipment. It is a standard hardware which will have multiple applications depending on the model of your unit, please make sure to check the appropriate diagrams for the correc...Read moret location and use of this part. Keep in mind this screw is made of durable metal and is sold individually.

This is an authentic component which is supplied directly from the original equipment manufacturer for use with Ryobi and Homelite handheld lawn and garden equipment. The flywheel has magnets on its side that create an electric charge as the magnets pass the ignition module. The electric charge is sent to the spark plug to fire the air-fu...Read moreel mix in the cylinder. The flywheel fits on the crankshaft by a key that aligns with a keyway on the crankshaft, this allows for proper firing timing. Keep in mind this high-quality flywheel assembly is made of durable metal and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component.

(M4 x 12 mm)

This is an authentic replacement screw which is supplied by the original equipment manufacturer for use with handheld lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. This high-quality Torx screw is made of durable metal and it is sold individually.

This replacement screw is a high quality hardware that is supplied by original equipment manufacturer for use with Homelite and Ryobi handheld lawn and garden equipment. This screw is a standard hardware which will have multiple applications depending on your unit, please make sure to check appropriate diagrams for correct location and use of this item. One durable metal torx screw is included per order.

This is a genuine manufacturer-sourced replacement screw which is specially designed for use with Homelite and Ryobi handheld lawn and garden equipment. It is a standard hardware which has multiple applications based on the model of your tool, please refer to the appropriate diagrams for the correct location and use of this part. It is made of high-quality metal and it is sold individually.