UT-08929-A Homelite Leaf Blower / Vacuum - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

Fuel Tank with lines and fuel filter

This crankcase cover gasket seals the crankcase cover of your lawn equipment engine, preventing air or fuel leaks and maintaining proper internal pressure. It is sized at 2 1/2 inches by 2 1/2 inches and is commonly found where the crankcase cover attaches to the engine block. You can tell if a crankcase cover gasket is broken if there is...Read more oil around the edges of the cover. Your machine may also experience a loss of power or unusual noise. If the gasket is not replaced, your machine may have fuel leaks or decreased performance. Debris and contaminants will also enter the engine, reducing the lifespan of your machine. When replacing the gasket, use a wrench or socket to unthread any bolts securing the crankcase cover. You will then be able to take the gasket off your machine. Bear in mind that this OEM gasket is sold individually.

Genuine OEM replacement part, this item is sold individually. This Fuel Cap is is on the fuel tank on the outdoor products shown below. This is a vented Fuel Cap. It includes a gasket inside the Cap.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

This is an OEM replacement part and is sold individually. Its purpose is to filter out dust and debris from contaminating the carburetor. When replacing the filter you can open the package in comes in and put a bit of two cycle oil in the bag and let it absorb into the filter. Then remove it from the bag and squeeze it with a paper towe...Read morel to remove the excess oil. This will aid the filter in filtering out the unwantables.

This is a genuine OEM replacement part, it is sold individually. The purpose of this part is to connect the fuel line extending from the fuel tank to the fuel line that connects to the carburetor. Over time the fuel lines will become brittle and oversized. They will have to be replaced. This would be a good time to replace the Fuel Fitting also.

This rope is part of the pull starter system on Homelite and Ryobi gas powered lawn and garden equipment. It is an authentic manufacturer sourced replacement part, not an aftermarket equivalent. When the rope is pulled to start the engine, it is returned back into the starter pulley by means of the starter spring which is sold separately....Read more Please note, this rope is made out of strong fabric and it is sold individually. Replacing this starter rope you will need a screwdriver. • Remove the housing-cover • Remove the carburetor • Disconnect the clutch housing • Bind the engine • Remove the clutch drum • Remove the clutch • Remove the starter • Remove the starter handle • Remove the recoil pulley • Remove the old rope • Install the new starter rope • Reassemble and test the unit

It is an authentic OEM sourced replacement item designed for use with Homelite and Ryobi handheld lawn and garden equipment. The ignition module also known as an armature-magneto provides an electric current for the ignition system. It produces high voltage pulses for the spark plugs. It is made out of metal with a rubberized wire and a spark plug boot. Please note, this ignition module is sold individually.

This is an authentic replacement screw which is supplied by the original equipment manufacturer for use with handheld lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. This high-quality Torx screw is made of durable metal and it is sold individually.