UT-08580 Homelite Leaf Blower / Vacuum - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This carburetor gasket is an OEM replacement part for use in a variety of lawn and garden outdoor equipment. It seals the area between the carburetor and the intake manifold to prevent air and fuel from leaking. Over time, the gasket may wear down, crack, or warp due to normal aging, exposure to heat and chemicals, or improper installatio...Read moren. A faulty gasket will cause air and fuel to leak, resulting in hard starting, rough idling, fuel wastage, and overall lower engine performance. To replace the gasket, remove the air filter cover, air filter, and carburetor. Carefully pull off the old gasket, and thoroughly clean the sealing surface of all residues. Place the new carburetor gasket onto the intake manifold, and firmly press it in place. Reassemble the equipment parts in reverse order to complete your repair.

This high quality fuel tank assembly is utilized on a Homelite blower. It is a genuine OEM sourced item, not an aftermarket equivalent. The purpose of this tank is to hold the fuel needed for the engine to run. This assembly includes a plastic fuel tank, the fuel lines and the cap. Over time it may deteriorate allowing for leaks and requi...Read morering replacement. Please note the hardware to secure this tank is sold separately. You will need a screwdriver to complete this repair.

Genuine OEM replacement part, this item is sold individually. This Fuel Cap is is on the fuel tank on the outdoor products shown below. This is a vented Fuel Cap. It includes a gasket inside the Cap.

Genuine OEM replacement part, this item is sold individually. The purpose of the 901551001 Intake Gasket is to create a seal between the Heat Dam and the cylinder head. Over time because of the heat it is exposed to this gasket will deteriorate and will have to be replaced.

This is a genuine OEM sourced replacement part designed for use with gas powered string trimmers and blowers. The ignition module also known as armature-magneto provides current for the ignition system by producing pulses of high voltage for the spark plugs. It is made out of metal with some plastic components and it is sold individually....Read more Includes a spark plug boot. To complete this repair you would need screwdriver set. Please note replacing this module would differ based on your unit, however the basic steps would be the same. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Install the red wire • Set the gap • Install the black wire • Reassembly and test the unit

This replacement part is sourced directly from original equipment manufacturer. This switch is designed for use with a variety of power equipment. It is an important piece of hardware responsible for handling on/off function of equipment. Because switches have internal mechanical part, over time they will break down requiring replacement....Read more This switch has a plastic body and it includes a clear plastic cover. To complete this repair you would need a screwdriver. • First make sure the unit is not plugged in • Then you want to separate housing pieces by removing screws • Disconnect wires from the old switch • Replace old switch with a new one • Reconnect wires • Reassemble and test the unit

This is an authentic OEM sourced replacement screw. It is specially manufactured for use with a variety of handheld lawn and garden equipment. This is a standard hardware which has multiple applications based on your unit. Please refer to appropriate diagrams for correct location and application of this screw. This screw is made out of me...Read moretal and it is sold individually. To remove or install it you will need a torx screwdriver.

This replacement screw is a high-quality hardware that is supplied by the original equipment manufacturer for use with Homelite and Ryobi handheld lawn and garden equipment. It is a standard hardware which will have multiple applications depending on the model of your unit, please make sure to check the appropriate diagrams for the correc...Read moret location and use of this part. Keep in mind this screw is made of durable metal and is sold individually.

This is an authentic component which is supplied directly from the original equipment manufacturer for use with Ryobi and Homelite handheld lawn and garden equipment. The flywheel has magnets on its side that create an electric charge as the magnets pass the ignition module. The electric charge is sent to the spark plug to fire the air-fu...Read moreel mix in the cylinder. The flywheel fits on the crankshaft by a key that aligns with a keyway on the crankshaft, this allows for proper firing timing. Keep in mind this high-quality flywheel assembly is made of durable metal and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component.

Genuine Homelite replacement part, this item is sold individually. A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below th...Read moree Venturi is a butterfly valve called the throttle valve ' a rotating disc that can be turned end-on to the airflow, so as to hardly restrict the flow at all, or can be rotated so that it (almost) completely blocks the flow of air. This valve controls the flow of air through the carburetor throat and thus the quantity of air/fuel mixture the system will deliver, thereby regulating engine power and speed. The throttle is connected, usually through a cable or a mechanical linkage of rods and joints. Fuel is introduced into the air stream through small holes at the narrowest part of the Venturi and at other places where pressure will be lowered when not running on full throttle.