UT-08510 Homelite Leaf Blower / Vacuum - Overview

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

Fuel Tank with lines and fuel filter

This crankcase cover gasket seals the crankcase cover of your lawn equipment engine, preventing air or fuel leaks and maintaining proper internal pressure. It is sized at 2 1/2 inches by 2 1/2 inches and is commonly found where the crankcase cover attaches to the engine block. You can tell if a crankcase cover gasket is broken if there is...Read more oil around the edges of the cover. Your machine may also experience a loss of power or unusual noise. If the gasket is not replaced, your machine may have fuel leaks or decreased performance. Debris and contaminants will also enter the engine, reducing the lifespan of your machine. When replacing the gasket, use a wrench or socket to unthread any bolts securing the crankcase cover. You will then be able to take the gasket off your machine. Bear in mind that this OEM gasket is sold individually.

Genuine OEM replacement part, this item is sold individually. This Fuel Cap is is on the fuel tank on the outdoor products shown below. This is a vented Fuel Cap. It includes a gasket inside the Cap.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

This authentic item is supplied directly from the original equipment manufacturer for use with Ryobi, Homelite and Ridgid handheld lawn and garden equipment. It is an identical replacement for a missing or a damaged bumper that was installed on a new unit. The part helps to secure the fuel tank in the housing. Make sure to check the appro...Read morepriate diagrams for your model for the exact location and the correct application of this component. Keep in mind this high-quality bumper is made of durable material and is sold individually.

This rope is part of the pull starter system on Homelite and Ryobi gas powered lawn and garden equipment. It is an authentic manufacturer sourced replacement part, not an aftermarket equivalent. When the rope is pulled to start the engine, it is returned back into the starter pulley by means of the starter spring which is sold separately....Read more Please note, this rope is made out of strong fabric and it is sold individually. Replacing this starter rope you will need a screwdriver. • Remove the housing-cover • Remove the carburetor • Disconnect the clutch housing • Bind the engine • Remove the clutch drum • Remove the clutch • Remove the starter • Remove the starter handle • Remove the recoil pulley • Remove the old rope • Install the new starter rope • Reassemble and test the unit

It is an authentic OEM sourced replacement item designed for use with Homelite and Ryobi handheld lawn and garden equipment. The ignition module also known as an armature-magneto provides an electric current for the ignition system. It produces high voltage pulses for the spark plugs. It is made out of metal with a rubberized wire and a spark plug boot. Please note, this ignition module is sold individually.

This is an original Homelite replacement part manufactured for use with lawn and garden equipment. This gasket forms a seal between the cylinder and head dam and helps prevent exposing the carburetor to heat produced by the small block. This heat dam gasket is sold individually.

This is an OEM part sourced directly from the manufacturer. The flat washer is designed for use in blowers from Homelite, Ryobi, and Ridgid. This part is made of metal, and is generally used to allow the fan to spin easily. You may require an Allen wrench or screwdriver when replacing this part. This item is sold individually.