UT-08052 Homelite Leaf Blower / Vacuum - Overview

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

This is a genuine OEM replacement part, it is sold individually. The purpose of this part is to connect the fuel line extending from the fuel tank to the fuel line that connects to the carburetor. Over time the fuel lines will become brittle and oversized. They will have to be replaced. This would be a good time to replace the Fuel Fitting also.

This is a genuine OEM sourced replacement starter rope, not an aftermarket equivalent. This part is used to pull start Homelite and Ryobi handheld lawn and garden equipment. This rope is made from durable fabric and it is sold individually. Please note, the grip handle is sold separately. Replacing this starter rope you will need a screwdriver.

This replacement piston ring is a high quality manufacturer sourced replacement part that is specially designed for use with Homelite and Ryobi handheld lawn and garden equipment. It is used to provide a seal between the piston and the cylinder walls. If this part wears your tool will not be able to operate as intended. Please note one durable metal piston ring is included per order.

This is an authentic replacement screw which is supplied by the original equipment manufacturer for use with handheld lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. This high-quality Torx screw is made of durable metal and it is sold individually.

This metal OEM wire clamp is a type of fastener that holds hoses or cables together and keeps them from moving while your machine is operating. It is mostly found in lawn equipment to attach its fuel line to the filter. You can tell that the metal clamp is broken if the parts it was securing has become loose or has fallen off. When this h...Read moreappens, your equipment may start leaking and can pose as a safety hazard. To remove the wire clamp, you need a pair of pliers. Grip onto a broken clamp before twisting it counterclockwise to release it from your machine. This item is sold separately.

This starter pulley is an OEM part direct from Ryobi. This part is compatible with a variety of lawn and garden devices. The pulley is most often fitted between the air baffle and the container w/spring within the starter assembly. Please consult specific manual and diagrams for repair instructions. This part is sold individually. A screwdriver and a hex key are usually needed in making the replacement.

This 3-inch-long flexible rubber tubing connects the fuel filter to the carburetor of your handheld lawn equipment, ensuring a clean and uninterrupted fuel supply for combustion. If broken, it may leak fuel due to cracks or holes, and the engine can stall, idle roughly, or have difficulty starting. If the damaged rubber tubing is not repl...Read moreaced, it can allow contaminants to enter the fuel system and clog the carburetor. It may also result in fuel starvation, causing the engine to run lean and potentially overheat. To remove the rubber tubing, first, ensure the engine is shut off and cooled down. Remove the wire and boot from the spark plug. Lift the tab on the air filter cover to release it, then remove the cover. Using a flathead screwdriver, pull the tubing from the carburetor ports. Use a torx bit to unthread the mounting screws that secure the fuel tank. Once the fuel tank is detached, you can fully disconnect the tubing. Keep in mind that this OEM replacement part is sold individually, so make sure to confirm the quantity needed for your machine before making a purchase.

This manufacturer sourced part is designed for use with Homelite and Ryobi handheld lawn and garden equipment. It an identical replacement for a missing or a damaged screw that was installed on a new unit. This is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model ...Read morefor the correct location and application of this component. Keep in mind this high-quality screw is made of durable metal and is sold individually.