This OEM filter is sold individually. Change your filter every 6 months for the best results. This filter is found in top-freezer and bottom-freezer refrigerators located in the back upper right corner. It measures 4.75-Inches deep 9.5-Inches high and 5.25-Inches wide. It is certified to reduce particles chlorine-resistant cysts lead and ...Read morefive other impurities. The pressure requirement is 40-120 PSI (if yours exceeds this you?ll need to install a pressure-timing valve) and the operating temperature needs to be 33-100 degrees Fahrenheit. It filters down to 0.5-1 microns. The installation is simple and does not require any tools or mess. To remove the old cartridge turn it to the left and pull down carefully. Some water might drip so keep a cloth handy. To install the new filter place it into the cartridge holder and turn to the right until it will no longer turn. If you have a top-freezer model it should be situated vertically and if it is a bottom-freezer model it should be placed horizontally. Be careful not to over-tighten. If your model has a replacement indicator light reset it by pushing and holding it down for three seconds. If your model has a dispenser run water through it for approximately 3 minutes to clear the system. Please note that this filter will not work in Kenmore brand models.
Water can still flow to the refrigerator dispenser and ice maker when the filter is removed by using this OEM bypass plug in the water filter head. Check your refrigerator model to confirm compatibility. Unplug the ice maker before installation. Side panel removal may be required.
A two-port solenoid valve regulates water flow to the ice maker in compatible refrigeration equipment. Check your appliance model before ordering this OEM part.
This 120 VAC solenoid valve controls water drainage from a refrigerator ice maker. It is an OEM replacement. Confirm fit using your appliance model number before ordering.
The power control board is listed for refrigerators that use flammable refrigerants, including R600a. Check the refrigerant type and parts information for your refrigerator before ordering. Disconnect power before servicing the appliance.
Pressure changes during ice maker operation are detected by this sensor and hose assembly. It is an OEM part listed for select ice makers. Confirm compatibility with your appliance model number before ordering.
This tubing coupling joins two 6 mm refrigerant tubes in the appliance sealed cooling system. It forms a mechanical connection without soldering or brazing when assembled with the matching tools and specified sealing compound. Both tube ends must match the fitting size for the joint to seal correctly. Follow the connection instructions fo...Read morer preparing the tubing and pressing the assembly into place. Confirm the required metric diameter before selecting the coupling, since 6 mm and 1/4 inch are not exact equivalents and may require different fittings. This is an OEM part sourced directly from the manufacturer.
This reducing coupling joins a 6 mm refrigerant tube to a 4 mm tube in the refrigerator or freezer sealed cooling system. It provides a mechanical connection without brazing or welding when assembled with the matching tools and specified sealing compound. Both tube ends must match the fitting openings for the joint to seal correctly. Foll...Read moreow the connection instructions for preparing the tubing and assembling the coupling. Confirm the required metric sizes before ordering, since nearby inch measurements are not exact equivalents and may require a different fitting. This is an OEM part sourced directly from the manufacturer.
This brass reducing connector joins an 8.5 mm refrigerant tube to a 6 mm tube in the refrigerator sealed cooling system. It forms a mechanical joint without soldering or brazing when assembled with the matching connection tools and specified sealing compound. Both tube diameters must match the fitting openings for the joint to seal correc...Read moretly. Follow the connection instructions for preparing the tubing and pressing the assembly into place. Confirm both sizes before ordering, since similar looking reducing connectors can have different openings and may not fit the same lines. This is an OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
I have weak thumbs
53 of 117 peoplefound this instruction helpful.
Lois from Green Valley, AZ
Easy
30 - 60 mins
Pliers, Screw drivers
Required pliers to remove old - be careful. New went in very easily per instructions.
Was this helpful?
Thank you for voting!
Water filter light came on in my refrigerator.
5 of 5 peoplefound this instruction helpful.
Barbara from KILMARNOCK, VA
Very Easy
Less than 15 mins
Pliers
Opened the water filter sleeve on the inside of my refrigerator. Removed the old water filter cartridge. It was a little stuck so I used a pliers to turn the cartridge counterclockwise. The old cartridge slipped out. I inserted the new cartridge and turned it in clockwise until it "clicked." Closed the water filter sleeve. Reset the butto
... Read moren on my fridge. All set to go.
Read less
Was this helpful?
Thank you for voting!
No water from dispenser, just a trickle
4 of 5 peoplefound this instruction helpful.
Nancy from PARRISH, FL
Really Easy
30 - 60 mins
Nutdriver, Wrench (Adjustable)
Troubleshooting was the most difficult job, but Parts Select helped with good info and videos. The water filter pushes down on a small plunger that allows the water to flow. If the water filter is bad or clogged up and needs replacement this plunger will not allow the water flow. I tried using the water filter bypass plug but this did n
... Read moreot solve the problem either. The plunger was defective or worn out. I ordered the filter & tube assembly from parts select, and followed the simple instructions to change it out. Turn off the water supply first and put some towels down because they’ll be a little spillage out of the tubes. Unscrew both of the tubes with a crescent wrench. Remove the two screws on the filter assembly inside the refrigerator, and pull it forward to take it out -the tubes will follow. Insert the new assembly, tubes first thru the hole inside the back of the refrigerator. Reconnect the tubes and remount the filter assembly inside. Stuff putty back inside the hole with the tubes and reattach the metal cover. This is an easy repair. I am an old lady, so the hardest part was pulling the refrigerator out to get behind it!