This assembly is the door shelf end cap set for the left and right side of your refrigerator. The function of the door shelf end cap is to attach the inner door liner to the door shelf rail. This will then hold the door shelf rail in place and keep it stable. To make this installation you may need a pair of pliers, other than that the par...Read morets will easily snap in and out of place. These pieces are white and measure almost 2 inches long, 1 inch high, and 1.5 inches wide.
This gasket retainer clip kit is for freezers. There are 24 pieces in this kit. The clips are what secure the gasket and liner to the freezer lid. The clips are white in color and made of plastic. If you notice frost build up in your freezer or that is it is not maintaining its temperature, this might be because the retainer clips have br...Read moreoken, and this has caused the gasket to become loose. This is a genuine OEM part that is obtained right from the manufacturer, ensuring a quality repair.
This is a shelf support for the left side of a freezer. It is used to help support the inside of the shelf from both sides. *Please note: right and left side of shelf support are sold separately. If the shelf in your fridge is unstable, replacing this part could be the solution. Make sure to unplug the refrigerator or freezer from the pow...Read moreer source before beginning this replacement project and safely store food. Follow the instructions in the diagram provided by the manufacturer for further instructions and guidance.
This is a plastic OEM drain plug that is attached to the drain system of your appliance and is compatible with several different makes and models of refrigerators, freezers, and air conditioners. This drain plug is used to prevent water from leaking out of the incorrect drain system within the appliance and is normally removed for cleanin...Read moreg and maintenance. If you notice water leaking inside of your appliance, the plug may be improperly positioned or may need replacing. To replace, simply pull off the damaged plug and insert the new plug in its place.
A filter-drier in a refrigerator has two essential functions. The first is to absorb system contaminants, such as water, which can create acids. The second is to provide physical filtration. This means trapping moisture, small metal chips, and dirt found in the refrigerant gas. If your refrigerator motor is constantly running, but the ref...Read morerigerator is not getting cold, the issue could be due to a damaged or faulty filter-drier. Faulty filter-driers are sometimes the cause for abnormal freezer compartment temperatures and partially frosted evaporators. This filter-drier is approximately 11 inches long. Remember to disconnect the power from your refrigerator before beginning this repair.
This part is found in freezers. The stud may have broken over time and may no longer be supporting the shelf. If your shelf is not staying in place or you are not able to adjust heights, it may be due to the support being broken. To complete this repair, you will need to open the fridge and remove the drawer and the shelf. To remove the o...Read moreld stud, you will need a 3/4-inch wrench to twist it off. The new part should push into place and will need to be turned with your wrench to be secured into place.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer stopped freezing food.
19 of 27 peoplefound this instruction helpful.
FREDDIE from WHITAKERS, NC
Really Easy
Less than 15 mins
Pliers, Screw drivers
I unplugged electrical cord to the freezer. I removed the cover to the relay and load protector. I labeled the wires and made a diagram on the proper placement of each wire going to the relay. I unplugged each wire and removed the relay. Then I removed the load protector. I installed the new load protector and new relay. I placed the wire
... Read mores on the proper terminals of the relay. I replaced the electrical cover to the relay and load protector. I plugged the electrical cord back in the electrical outlet. My freezer started working again. I placed several bottles of water in the freezer to make sure the freezer was working properly before I restocked it with food.
Thanks again for the help. You just saved me about $400.
While defrosting freezer tossed the drain plug with ice and water into the sewer system.
4 of 5 peoplefound this instruction helpful.
paul from LISLE, IL
Very Easy
Less than 15 mins
Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.
Was this helpful?
Thank you for voting!
end cap broke
3 of 4 peoplefound this instruction helpful.
GEORGE from WEST LIBERTY, OH
Really Easy
Less than 15 mins
slid one end cap into slot and pulled into place. Put other end cap into cross bar and put other end of cross bar on to other end cap proceeded to put other end cap in to other slot in door and pulled into place. Job complete Job took less than three minutes.